Cleaning the polymer of a polymer pistol

Status
Not open for further replies.

Erief0g

Member
Joined
Mar 13, 2018
Messages
660
Location
Charlotte, NC
So you've just done a full cleaning of your polymer pistol. Hands got oily and maybe got a bit of stuff on the plastic. Maybe but it with synthetic safe gun scrubber and even safe it seems washed out a bit.

Need something to clean, protect, and most importantly not make it slick?!

I've been using plexus plastic cleaner for over a year now. I used to be in the motorcycle business and the product was born in the aviation field.

Link to mfg.
http://plexusplasticcleaner.com/about.html

Pricing seems all over the place so if your interested try calling a local bike shop and you may find the best deal. For firearms a small can still goes a long way.

Figured I'd share since it really does work great and I never see similar products at any gun shops around my area
 
Plexus works well to clean the faceshield on a motorcycle helmet and a plastic motorcycle windshield. Isopropyl alcohol works for me to clean a polymer pistol frame.
 
Last edited:
I used a alcohol. Some of the plastic cleaners seamed to leave a slippery film on the plastic. I barely use more then a bare tooth brush to clean the carbon off. Once in a while i spill lube on the frame, then i use the alcohol.
 
I use Hoppe's No. 9 followed up by some FP-10 and then wipe it clean. Has worked for decades.
 
I've had good luck with alcohol, soap and water, and just a warm, dampened rough cloth like a shop towel.

If the polymer is greasy, try a warm damp cloth and lava hand soap, followed by clear warm water.
 
My Glock has never been dirty enough that a clean, dry rag was all that was needed. Although afterward I rub down the polymer with a rag with some Armor All on it. That stuff can also remove light amounts of dirt, dust,etc. and is great for all types of polymers, plastic and even rubber. I've heard that any of those polymer materials can be effected by excessive amounts of UV rays. Never heard of a Glock being affected by that but I'd rather not take chances. I've used Armor All on other plastic, vinyl, and rubber that gets a lot of sun and it works. Even works well on rubber that rarely gets any sun. Keeps whatever type of polymer Glock uses looking like new.
 
Old terry cloth towels lightly damp with water/Dawn.
Cleans, degreases and leaves polymer very grip-able.
 
Boil it for 10 minutes and hang it out to dry over night.
...kidding.
I just blast them with compressed air and wipe with a damp paper towel, that always seemed to be enough for me.
 
If you put Talon grip panels on your polymer pistol, they tell you to clean the grip with isopropyl alcohol before you put on the grip panels. I had these Talon grips on my G-19 once and didn’t like them but I’ve used isopropyl alcohol on polymer grips ever since then.
 
Last edited:
An ultrasonic cleaner does an incredible job on plastic and rubber. It removes all the tiny micro particles and leaves an incredible grip. Golf clubs are often cleaned in ultrasonic cleaners to restore the grip on the grip. After a big oily messy project I will often toss my tools in the ultrasonic cleaner... screw drivers, wrenches, etc. are a lot easier to hold onto after wards. I tossed the original plastic vent cover out of my 67 F100 once... it came out looking like brand new plastic.
 
Dawn dish soap
If you can clean baby ducks with Dawn...you can clean anything ...and it won't be slippery .
When I bought new prescription glasses with coated high tech lenses , I was told by the Doctor and two different tech's to clean them with water and a few drops of Dawn ... it wouldn't damage/remove the high tech coatings !
Gary
 
I use a Kleen Bore silicone gun cloth to wipe it all down and clean it off. Then I wipe it off with a cotton rag.
They clean up great this way.




My Glock has never been dirty enough that a clean, dry rag was all that was needed. Although afterward I rub down the polymer with a rag with some Armor All on it. That stuff can also remove light amounts of dirt, dust,etc. and is great for all types of polymers, plastic and even rubber. I've heard that any of those polymer materials can be effected by excessive amounts of UV rays. Never heard of a Glock being affected by that but I'd rather not take chances. I've used Armor All on other plastic, vinyl, and rubber that gets a lot of sun and it works. Even works well on rubber that rarely gets any sun. Keeps whatever type of polymer Glock uses looking like new.

The problem with Armor All is once you start using it on certain synthetics you must continue to use it from now on. If you stop the synthetics become brittle or suffer cracks. That will happen with vinyl and some plastics. I do not know if that problem could occur with advanced polymers like on a Glock frame.
 
Mostly a damp rag. Dawn works great, but smells so bad, I won't have it in the house. I have talked to people who insist Dawn has little smell. Something is wrong with them.
 
Mostly a damp rag. Dawn works great, but smells so bad, I won't have it in the house. I have talked to people who insist Dawn has little smell. Something is wrong with them.

Dawn comes in a bunch of scents. Fruity, Fresh, Natural, Herbal, etc.....Palmolive is the least offensive for me. A damp rag works. I agree.
 
For those cheap plastic guns (most of my ”collection”), the top rack of the dishwasher generally works fine for me! :thumbup:

Seriously, I don’t think I’ve ever used anything but the same cloth I use to wipe the entire gun down at the end of a cleaning or shooting session...microfiber car cloth with some residual Ballistol on it from wiping down the gun (just a dab will do ya!:cool:
 
Don't overthink it. LOTS of different plastics, and those (many) used for firearms frames are really not delicate flowers. They can handle normal gun cleaners and solvents just fine.

I used Hoppes for a long time, now also a Ballistol guy.
 
Status
Not open for further replies.
Back
Top