Viewing the opening of a partially withdrawn slide would reveal any case, empty or loaded, in the chamber or held by the extractor.
Commonly known as a "Press Check".
Continuing on to slide lock would eject any case held by the extractor.
jmo,
.
500 yards.
Do you get to drive out to the 500 yard target line to setup targets??
I hope you don't have to carry that bag-o-targets out there!
How do you transport the target frames?
Are they the sawhorse type or a base and upright, or a stake driven into the ground?
Post some pics of your...
Have your friend open that 750 box, pull out the manual, and tell you how many pages that manual has.
Compare that to your 6-pack manual (I'm thinking 4 pages max), and you will see how setting up that Dillion will go...
jmo,
.
What do you use to bulge bust 9mm??
I have read of some using a 9mm MAKROV SIZING DIE, removing the de-prime pin, and pushing 9mm case thru the die.
...Or push the case completely into the die and knock it out via a punch from the top.
https://www.midwayusa.com/product/1011210541?pid=708065
or...
So, I'm thinking your google search revealed there is no return spring on the Lee Powder Drum as it has an internal spring.
If there is interference with powder check die Lee sells a riser for the powder thru expander die for like $8 at Titan, and I run 2 of them stacked on my piggyback to clear...
OK, a respirator instead of goggles then :rofl:
Risking a room uninhabitable for a while and having to clean it out of the carpet is better than recovering from an attack, IF you survive it.
Never said inside the house, but that asshat husband deserved a spray or injection of something...inside...
I have a couple of dueling trees 1 centerfire, 1 rimfire and are petty gangling when assembled.
I made a wooden box for the paddles and the tree "trunks" fold up flat.
I use a cheap harbor freight hand truck to move that stuff around.
Box:
.
Why not skip all that and start out wet tumbling with pins...
You are going to end up there anyways, once you realize that cleans the de-primed primer pocket squeaky clean.
That primer smooge is what cruds up your press and causes most/all loading problems (for me).
You can start out with a...
Yeh, Galloway makes a short stroke trigger/spring kit for the SCCY but has been "out of stock" for some time and I emailed about it but they have no remakes in their schedule...
https://gallowayprecision.com/sccy/cpx/short-stroke-trigger-kit-for-sccy-cpx-pistols
I have swapped out the hammer...
You're almost there.
No drama using these:
Pre heat it, using a soldiering gun to localize the heat.
Often the lefthand drill end does the trick.
Set the drill clutch/ratchet for minimal torque and work your way up.
jmo,
.
Just know that the SCCY CPX-9 is a clone of the P-11 and in production NOW.
I have a couple and they have been rock solid for me and only $179 when I bought them.
I prefer DAO guns for the safety aspects utilized in practice.
Most have no safety; no de-cocking lever and I can thumb the hammer...
Thanks for posting.
That fold-over/clamshell method can be the most expensive method, because you have to design/build a mold core.
Most makers use those blue dummy guns as a core to make a 2-piece (front/back) holster and glue on channels to the blue gun slides /top.
Like a sight channel...
yeh, but most who dress "that way" have to know the image they project and should expect some to judge them accordingly.
The same as most of us are judged by age/gate/mobility/etc.
.
Yeh, but their clean clothes, $70 haircuts, and 200k bike gives them away as posers.
That and their same age, primped up, French Manicured "old Lady".
been there, seen that.
.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.