Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
You are using the old High Contrast theme. We have installed a new dark theme for you, called UI.X. This will work better with the new upgrade of our software. You can select it at the bottom of any page.
I’m a fan of both the round and the Makarov (a work of art in its simplicity).
With just a hair more oomph than .380, I agree with RevolvingGarbage that it’s a good minimum defense round. My Makarov stays loaded with +P hard cast flat nose for that purpose.
Interesting article. Seems like it's essentially an in-situ heat treatment of the alloy - the last layer before a pause is essentially allowed to "quench", and the heat applied by subsequent layers allows precipitation of Ni3Ti, whereas the first layers may be homogenizing .
This seems like...
Aluminum has limitations in certain areas, just like steel, and can by no means be stated as completely inferior to steel. If properly designed, an aluminum frame is a perfectly suitable design choice because of the corrosion resistance and weight advantages noted by many others.
I am a...
The microstructure is predominantly ferrite with small amounts of pearlite - pretty much pockets of it scattered about. As the carbon fraction goes down, the amount of pearlite diminishes (or in some cases is just cementite) until carbon is about 0.008% by weight. Below this, the structure is...
Time for me to jump back in. Permanent deformation at room temperature by stress relaxation in springs has been addressed in academic literature since at least the 1970's. This mechanism is completely different from both fatigue and creep. You are correct that creep is not operatimg in any...
It depends on the tempering temperature used for the steel part as to whether it will be affected. Short duration exposures up to the tempering temperature will have no substantial effect. As an example, if the part was tempered at 600F, the temperature would have to be higher before there's a...
Part of the problem with using sag as an example is that it describes a symptom. The symptom could have multiple causes - stress relaxation, wear (e.g. fatigue), overload, etc. There are research papers which document stress relaxation testing methods with reference to sag resistance, so it is...
...composition on sag resistance of suspension spring. No. 820128. SAE Technical Paper, 1982.
Murai, Teruyuki, Seizo Takamuku, and Nobuharu Takeno****a. High sag resistance spring wire for automotive suspension. No. 850059. SAE Technical Paper, 1985.
Borik, F., V. A. Bišs, and Y. E. Smith. Sag...
I'll tentatively plan on doing this experiment. I have no experience using load cells, but this will be added to the list. Seems like it would be well worth the relatively small investment to put some real data into this debate.
Bean counters will not make those decisions, but they will set cost targets that force engineering to get creative and/or make compromises. Pretty standard occurrence from my experience. Something like that could have prompted a design review, and determined that polymer was OK for a guide rod.
Thanks for doing the test. That 180gr XTP seemed to do alright in 10mm. Makes me feel better about the two types of ammunition I currently have that use it.
It certainly seems to be the hollow point of choice for a number of 10mm loadings.
I agree with the above. Unless there's a history of failure (e.g. bad design) for the polymer guide rod, I see no reason to replace it with a metal one.
This discussion happens frequently enough that I'm considering running a quantitative test to evaluate different springs.
It's in the brainstorm stage, but I'm thinking of setting up an inexpensive load cell with data acquisition to generate a relaxation curve for a sampling of springs over...
Guess I can join the club now with my new Glock 20.
Took it to the range Friday, which was my first time shooting a Glock and first time shooting 10mm. That trigger takes a bit of getting used to, and I started out terribly at 7 yards. After 160 rounds I was doing OK, though. Need a lot more...
Yes, the springs certainly can weaken over time (causing failures to feed), and there are several threads containing explanations of how and why this happens.
However, a quality spring will have been designed to account for long term compression and won't have any issues. Note that even good...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.