Just Set Up #-3 550-B...
The 1st was a plain 550 , then later came the upgrade to [ B ] the later 2 were the 550-B. Have 2 -in small Pri & one in Large Pri mode.. As I only have place for 2 on the load bench , I have gone to Pat Marlins "Rock Dock" bench mounting Sys, Thyt are really soild...
Kesselrings Closing ... Fact...
Just got off the phone with along time co-worker & friend that lives about 10+ miles from that store . It is happening , don't have an exact date , however it is True. Rumor around the area is that there record keeping of guns in & out weren't up to snuff ...
44 Rem Mag Trim Length...
I have a sheet that I printed off in 2000, from some place & it has 1.285 -1.280 numbers on it . However there is an by the numbers & I have no idea what that did refer to ,didn't get that info when it printed. My 2¢. Russ.
Thanks Guys , Appreciate the Input...
Yrs ago I used RVO then they faded away , I did get my brass back ,some didn't. Think I will give the guy in Texas a Go. Am planning on keeping the Brass & reloading most of it.. Again Thanks for your Help ... Russ.
I have a bucket full of 1x fired LC 01 cases. Not looking forward to all the work involved to get them ready 2-Reload . Does anyone know of a place that will fully process 223 brass & return to sender ??? Fellow that went by [Greygoose] did back in 09 & 10, however can't seem to locate Him now...
I disassembled some old 222 reloads one time,and as I dumped the powder, out came a burnt folded paper match. That still remains a Total Mystery to Me. Don't think that went thru a powder measure. Can only wonder if some one was trying to play a Joke on the reloader or a kid was goofing around...
Just wondering if anyone had an answer for the Crimping on the NT case. Sure is a Pain to reload those , getting rid of the crimp with a Dillon swager works, but some of the flash holes on the inside of the case have a long/large Burr that I have to deburr before I can even get them on the...
I have the Lee Classic turret also & really like it. The only draw back to the adjustable bar is the limit on the Capacity . I don't have the Lee catalog close by , but there is a top end on the amount of powder that it will drop as I recall. [Volume wise that is.] I ordered the double stack...
Benchmark, is what I have switched to from Varget. It is a bit faster but meters better I think. I use both in the Dillon powder measures on a couple of 550's. My 2¢ Russ.
Pact & Fluorescent Lights.
I have 2 pact scales & the dispenser, the only thing that I have noticed is that the scales some times will turn on. When using the comb for dumping powder I have 'Never" had any problems with that operation. I leave both the scales plugged in all the time & turned...
Call Dillon,they gave Me an adjustment sequence that was not in the Original manual. It tunes up the feed mechanism to where I now have "0" primer feeding on both the 550's I have.
If your not reloading then U-R-SOL. If you shoot the Full up factory stuff. Spl is hard to find these days it seems. I reload & have a pair of 44's. I also cast some. I like the Kieth 429421, 245 gr Semi-wadcutter. Load 14 grs in spl case & 16 grs in Mag case of 2400. Can plink with that load...
Never had a problem with my Pact near florescent lights. I did the Speed up Grade on the Pact last yr & that was a good $50 spent. In fact I still think they sent Me a new measure , is quick & more accurate then the early model. Some times the scale will turn on, I leave the scale plugged in...
Have two Simmons & they have been OK so far. But they are on lighter recoiling rifles 223 & 20 Tac.
I with jcwit on the BSA scope [Been Screwed Again]... My 2¢. Russ.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.