Search results for query: *

I am a big fan of SIGs and have several different models of the older German made ones with stamped carbon steel slides. They are well-made and very accurate right out of the box. I haven't been in the market recently so I don't know current prices, but I personally would be wary of a...

Congratulations! You can get a better idea of the build year of your P225 from the two-letter proof date code that should be on the bottom front slide chin of your pistoll and following the link provided by Ignition Override to decode it.

The gun looks a lot like a P229 Classic 22 that was designed so it could be converted to centerfire calibers using Caliber X-Change Kits. Unfortunately SIG discontinued these kits. Is there a label on the box or case? The model number would normally be on one of the labels. The P229 Classic...

I wonder if a P228 slide would fit onto a P226 frame with no modifications except for maybe a locking insert change? You would have your wish. BTW the prototype that WVsig mentioned was a chopped P226 frame with a P225 slide and marked as a P226C. This was done at the SIGARMS Tysons Corner...

Update: That prototype P228 was purchased by a diehard P228 fan on that forum.

I remember seeing a thread about that prototype on one of the gun forums that included photos. It must have been posted by that guy. I seem to recall there was a debate as to whether the pistol was a fake and it was a scam. What I can't remember is if that gun was eventually sold to someone...

Went back to look for the P225 reference earlier in this thread but couldn't find it. I must have either read it in another forum or I dreamed it up. Apologies for bringing it up.

Since it looks like no one has answered yet, yes you are correct. The "Exeter NH" is an import mark for those made in Germany with the German proof marks, normally located on the bottom front chin of the slide. FYI there are "Made in W Germany" marked slides on post unification guns made...

My Ruger Mark II Target MK-512 with a 5 1/2" bull barrel. It is accurate with no recoil, reliable, and the ammo is cheap.

I thought the desirable Electroless Nickel finish on SIG pistols was done by Klein who did the "factory" nickel plating for SIG in the '90s.

AFAIK SIG did not make any stainless steel frame guns in 1995 and the only stainless slide (marked "STAINLESS" on the slide) pistols were the P229 until 1998 or 1999.

The M11-A1 is basically a 9mm P229 with no rail, phosphated internals, and SRT standard, so yes, the P229 is as good as the M11-A1. If you are actually talking about a P229 Legacy, then it will have an old-school Legacy slide that has the short external extractor and the half-height serrations...

That's OK. It was the OP who brought it back to life. Besides the P228 is timeless.;)

Could you post a pic? I always thought the Browning .45 BDA was just a re-branded SIG P220 with its own set of serial numbers. All P220s I am aware of have guide rods and standard recoil springs.

What weight Wolff mainspring is he using? The P6 normally uses a 28lb while the P225 uses a 24lb spring. I have a 22lb Wolff mainspring in my P6, but have heard of people using as light as a 19lb spring with no light strikes. I would suspect it is an issue with the firing pin and/or channel...

The Extreme Elite P229 has a hard black anodized frame, which means that it is alloy. That may be what RON has. http://www.sigsauer.com/CatalogProductDetails/p229-enhanced-elite.aspx To get a steel frame P229 it will have to be stainless steel, either a Stainless Elite (natural or nitron...

I can tell you a few facts, as I know them, about the older P220s with the stamped carbon steel slides. The 1987 you are looking at is pretty much the original design with the pointed hammer spur. Around 1993 and serial number G211300 SIG reinforced the frame, which can be seen on the right...

I voted for the P229 because it was specifically designed for the .40 S&W round and handles it quite nicely. If you were going 9mm, then I would have voted for the P226.

BTW SIG stainless steel slides don't have roll pins holding a separate breech block so that is one less maintenance thing to worry about.

The serial number puts your gun around 1988 so the frame may be German made, but the stainless steel slide was made in the US and did not exist in 1988. I suspect your gun was a SIG CPO (Certified Pre-Owned) which is a factory refurbished gun which can sometimes include a replacement slide...