Search results for query: *

I just picked up the new SR 1911 Commander style and was shopping for mags. I ran across a Wilson Combat and picked it up. It would not fit. The magazine would not lock in even with the base plate removed. It also would not lock the slide back. I ended up taking the pistol to the LGS and...

Have one that I can't remember seeing on here before. I do remember something about neck tension should be around 50lbs, not sure how to check this. I was working up some 10mm this morning, on inspection some of the bullets seated a little crooked. I pulled these down with my collet puller...

So there I was, working some 38s. I put a minimal flare on them and went on along. I have heard this stuff with thin wall's sucked before but just found a batch that had 0 neck tension. I could seat them to the cannelure by hand. So I pulled them down (15 of em) re sized and put no flare on...

I have been looking around and trying to find a digital copy of reloading manuals. Seems so much easier to keep them on a digital device (iPad in my case). Anyone find or use anything like this?

I searched the forum and googled this but wondering what mods are out there for the RCBS swagger with the Lee challenger press? I have a piece of pipe over the ram now that seems to be working but wondering if anyone else had found a fix.

Just kind of wondering. What real advantage is there loading really any rifle on a progressive? I picked up a shelplate for the lnl and after thinking about it I am not sure its worth the setup time for .223. Still have to lube, and trim after sizing taking most of the speed out of it. I...

Well I got a new toy today...Bushmaster XM 15, M4 style A3 and went to making up some rounds for it. Well as I finish the first 50 I remember something about Remington primers and a warning about certain caliber. Well low and behold I primed the 50 of them with 61/2's....Bummer, looks like I...

Well I just ordered a Wolf BBL for my G20 10mm and was wondering if anyone has experience with them. Wondering if I should go ahead and order some new brass as I have seen some other calibers on threads that had problems chambering brass from the factory bbl with any bulge in them. Trying to...

I was just loading on my LNL, and have found my Starline brass that I just tested some loads in is extremely hard to re size and leaving rings of brass at the bottom when I really force it. Before sizing they had no signs of pressure other than a small guppy bulge. I fired it from my G20, and...

Of the issues I have seen on here this one is not one of them. I was in the middle of loading some BD in 10mm and my metering assembly popped out mid stroke. Nothing broke, but an attention getter as powder started going everywhere. It was like twister with my thumb in the hole and trying to...

Does anyone have a powder recommendation for 10mm 155's. I use blue dot with my 180 gr's and they are spot on grouping at 1" at 15 yards. I tryed the blue dot with the 155's and they are all over the map. I ordered the 500 free xtp 155's with my press and want an accurate round to use for them.

Doing some research on the Lone Wolf Barrel's and saw in their FAQ's referencing case bulge on the 10mm/40, and a recommendation to use the redding die to eliminate this. Is this something that I need to worry about if I keep the stock barrel? It talks about chambering issues because of the...

Looking for a bit of advice on which to go with. Don't know if there are reloaders that have used both but was wondering for strictly pistol rounds if there are any recommendations, pro's/cons on these 2 dies besides the obvious. The Hornady is a visual only, and I have read a few reviews as...

Does anyone have a published load for 180 gr cast 10mm for blue dot? The only book I could find a 180gr load was Hornady and it did not have Blue Dot. I may end up with bullseye, but I was trying to stick with the blue dot, I use on the jacketed. I may just end up reducing by 10%, but wanted...

I am new to reloading, but think I have done a considerable amount of homework. I first off have a Taurus 605 .357 Mag that I enjoy firing .38 Spec out of. My first batch was with a 110gr bullet with 7 gr of HS 6 and had a stuck bullet. I thought that this was strictly an error on my part but...