E.N. Santa Barbara 1858 Remingtons ??
Smokin_Gun,
I have never heard of them. The hardened steel would be a plus to me. I have always been disappointed in the soft steel used in most Italian replicas. The engraving looks very nice too. Is the right grip panel on the lower...
$250.00 ??
"I don't see this 'ruffling anyone's feathers'. I don't know of anyone who would reasonably claim a $250 gun would compete equally with a $1500 gun."
I certainly agree with the concept of this but will add that if you can still find Old Army revolvers for $250.00 you best buy all...
Ruger Old Army
I like the Ruger Old Army revolvers.
No...they don't balance as well as a Remington 1858 or a Colt 1851.
The weight of a 7.5" barreled adjustable site Old Army is 2 pounds 14 ounces.
The advertised weight of the reproduction Walker can vary from 4 pounds 4 ounces to 4 pounds 8...
My NAA Experience
I ordered a NAA Mini .22 short model several years ago. If my dealer had not ordered it special for me I would not have accepted it. The serial number stamping is so out of line that one of the numbers are at least half the height of the number out of line with the other...
AdmiralB,
I think you are referig to the older plumber's solder. The folks here when they mention "plumber's lead" are refering to the thin sheet soft lead that you would find in an old shower pan liner. Most plumber's solder used today contains no lead at all.
Okay... I will play too....
I am more of a single action fan than a double action fan. My vote goes to Freedom Arms. I own several and have plenty of Colts, Rugers and Smiths to compare them to. The Freedom Arms revolvers are expensive and I would not buy them If I did not feel they are worth...
Novety Guns
I will admit to owning a S&W 500. It never comes out of the safe. I do like large bore revolvers with lots of power but in a packable size gun. My .50 caliber Old Army weighs very close to the same as it did before the conversion and has a shorter barrel so it is actually a bit...
Okay..that one was just too big.....
Perhaps a bit smaller would be in order:neener:
One Inch Bore Cap & Ball... The guy holding it is the maker:uhoh:
And then there is always the modern cartridge revolvers:what:
You Asked For It!!!! LOL
Well since we are comparing size here...chew on this for a while:neener:
Nope it is not mine...but I do think it is real. Sombody sure had some time on their hands.:rolleyes:
209 Shotgun Primer Ignition
Rachen wrote:
They mentioned that it was engineered for modern inline M.L. using 209 ignition right on the website. I am curious if it will perform well at all with percusion caps. I have little doubt that it will perform well in a modern inline with a 209...
Rim Dia. - .475 Linebaugh for FA vs .500 S&W
plinki wrote:
Actually the rim on the .475 Linebaugh brass that is sold commercially is smaller in diameter than the .500 S&W rim. The rim diameter of the 45-70 that the .475 was originally made from will not fit in the Freedom Arms revolver. It...
plinky has it....
This exact thing has been done by a few custom smiths on this exact revolver for years now. I wish it just had a simlple rim design instead of the belt. If there really is a reason for it I fail to understand it myself and I own one. They are nice guns though. I have never...
I understand...the belted issue
kentucky bucky,
I fully understand your point, agree with it and still I have no answer to it. As I said I think they could have done this without the belt. If custom smiths can the the original manufacture can. If it were beltless the...
The belted thing
I think they could have done this without the belt. A few custom smiths have been rechambering the model 83 to a shortened 500 S&W case for years with similar balistics. I wanted it because it is a Freedom Arms...not just because it exists. I wish they would have done it...
What good does it do anyway???
I noticed in the picture they are already using a lubed felt wad (wonder wad) between the powder and ball. Chain fires that are starting from the face of the cylinder are caused by a bad fitting or deformed ball that allows fire around it to reach the powder. If...
Why You Ask??
It is manufactured because people are willing to buy it. I already have some 50 caliber custom guns but I bought it because I am a Freedom Arms fan and collector and because I just wanted one. That's all the reason I needed. I can't say I have a practical use for it as my little...
The belt works fine forheadspace
DWFan,
Check out the link below for information on the cartridge. It headspaces just fine on the belt. I don't know how much the design was needed as I never had any problems shooting 385 grain extra hard cast bullets at 1500 FPS from the .50AE in...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.