Search results for query: *

A friend of mine dropped this off. No bolt. Definitely looks arisaka but wood goes to end of barrel vs almost to the end. No wood on the top of barrel. Any ideas

A friend found this rifle at his fathers house. Any ideas.

I have an M1 Garand in 308. Got it from an old man at church who was 90 and shot in matches in early 60’s. So I have been shooting it for couple years single shot. So today I used a clip and on the 4th shot I got 2 shots. Loaded clip again and it happened 3 times on that clip. Uggh. I reload...

I just started reloading 9mm. I resized and insured trim etc. I belled the case just enough to get bullet in. Then seated the 115 gr bullet. Using unique with 5.5. I did 4. All chambered and extracted fine. Primer looks good. I did notice some smut on each side of brass after shooting them. Any...

So i get out my sierra reload book and look up data. Decided on 4350 pwder as it was indicated most accurate. Loading 300 gr sierra hpbt. The powder range is 72.9 to 78.2. I started at 74.4 than incremented .5 all the way to 78. At 76 the bolt was difficult to open. All the wat to 78 grains...

I just bought a savage 338 lapua magnum. Got all my reloading stff and thought i was ready. Got ready to prime so i checked the lee shell holder with my cartridge before slipping it into the auto primer. Fit perfect. I then slid it into auto primer and then tried to insert cartridge and the darn...

I just got my savage 112 lapua magnum. I went ahead and bought some ppu ammo 250 grain. Will use for sighting then reload. I have looked some what for loads. Looks like retumbo or h1000 are good powders. And loads appreciated. One question though. I pretty much have always usde win large primers...

I have several 30-06 cases that have a small dent. I just resized 50 and only 3 has those dents. I believe they were already there as i got them from range. My qustion is - will that small dent cause any issues. So one te case is fied it should fire form and not allow ant qas to back flow. Head...

I have a lyman press and have not had good luck with them. This is my second in 10 years. I was full length resizing some223 brass and the darn rod that connects the turrent to the main part of the press broke off inside the main part of the press. Arghhhh i had this 5 years ago and thought it...

Just bought yesterday. Couple of questions. It has the cutout of course. They say stock should have a notch. Dont see it. Stock looks like a scant style. Not sure if original stock. Barrell is 11/19 so probably original. Hope I got a decent deal. Very good shape. Using the cmp bullet gauge at...

Thinking of getting a kreiger barrel from fulton armory. Will let them install. Has any one had any dealings with them on something like this. Barrel is at a 5 now. I shoot it for accuracy so feel like it is time.

I recently acquired an Egyptian hakim and have a question regarding the front sight. There is a screw that you use a flat head screw driver on to adjust windage. There is also a small hole on the other side. Does it or is it supposed to have a small screw to keep the sight from wiggling. There...

I have a set of sights i need help identifying. A friends dada died and left a bunch of rifle accesories. Trying to figure out thr part number. It was in a dp box labelled usa 431 but after looking at pictures online i dont think so. Also have a tunnel.

An elderly gentleman gave me this rifle. It appears to be a k98. It has no german nazti markings. None of the numbers match. I have a k98 with all matching i got years ago. Cant figure this one out. I do notice the front site is in the wood where mine is all metal. It is also shorter. The...

I just got my Redding dies and was so excited to finally be able to load for this. Well I worked up a round and then decided to test fire it. Well I got a click and not bang. I ejected it and tried it several times. Nothing - not a dimple or nothing. Listed below is my load: Norma 6mm BR...

I have a back order with midway for dies. Since December. I want rcbs. Called them and they say end of April. I have tried other sources and no luck. I have had my new rifle since last November. Just hard to believe they are so hard to get.

I have a savage I just got and trying to gather loading info. I want to use 70gr Sierra hpbt with varget. Have Norma brass. Rifle has 1:12 twist. Just to make sure I have this data correct. Keep seeing diff info. Trim 1.555 with 1.560 max Coal 2.441 I also have h4895 as an option...

My wife surprised me with a 1917 eddy stone for Christmas. Anyway I have a question or two. The bolt and receiver match as to numbers so that is cool. Barrel has 2-18 and is an exceptional shape. Rifling looks fantastic. Has all the markings it should have from what I can see. One question...

This keeps nagging me. When i measure coal i seat the bullet in the cartridge than measure with my calipers. i put the caliper on the tip of the bullet and of course the base. for example i use 2.800 for .308 sierra 168 gr hpbt. so i get it close lets say 2.794. so every few i check and i keep...

A friend of mine was looking at AR's and asked me a question i could not answer. he was looking at the bushmaster model 90689 carbon 15. i know nothing about the carbon piece of this. what are they talking about. i only buy rock river and i am very conservative. i like the basic A2, anyway what...