Search results for query: *

  1. T

    garand re-barrel

    thx for the reply sunray,much appreciated.
  2. T

    garand re-barrel

    hey fellas,getting ready to install a n.i.w. s.a.06-52 barrel on a jan.45 reciever, is an anti-seize compoiund on the threads nessesary? if so, what type of anti-seize compound is best/recommended.
  3. T

    gas cylinder bearing specs. m1 garand

    Orlando,jim k thx for the info,i had ordered a"6n1" guage from brownells and it has guage for the bearing and it measures .5970 and after posting my question,i finally found info on garand gear.com and their claim is the minimum diameter is .5991 - maximum .6000 -.7000 but my rifle functions...
  4. T

    gas cylinder bearing specs. m1 garand

    hi all does anyone know the specs.minimum/maximum diameter of the gas cylinder bearing for the m1 garand? thx in advance
  5. T

    gas cylinder bearing specs.

    ok thx will do
  6. T

    gas cylinder bearing specs.

    hi all just a quick question.does any know what the minimum/maximum diameter specs. of the gas cylinder bearing on the m1 garand?any help would be greatly appreciated
  7. T

    garand timing

    it seemed fine to me, before, but i caught a chance to get some NOS parts to help it last 2 lifetimes and it seemed to function fine never had a feeding issue never ejected the clip early or anything else out of the ordinary. but now, its functioning differently from what i was used to and it...
  8. T

    garand timing

    hey fellas i just had my garand rebarreled with a NOS sa 3-52 barrel and an NOS bolt ( post war) NOS op rod and cylinder now i have a concern, not with the smithing but timing. before all the new parts when i loaded a clip as soon as it seated and latched the bolt would release..NOW, after the...
  9. T

    m1 sights

    ive got that area covered just ordered a complete set from orion 7 it was a bit pricey $ 155.00 but it has everything thx again
  10. T

    m1 sights

    thx apachecotodd
  11. T

    m1 sights

    does anyone know what type of rear sights was used on an oct.1944 s.a. m1 with a serial number range 318xxxx i think it might be a type 3 lock bar but not sure any help will be greatly appreciated
  12. T

    garand muzzle gauge

    what all needs to be considered when using match ammo such as...... maximum grain bullet...gas plug etc,etc.
  13. T

    garand muzzle gauge

    im using surplus greek ammo the reciever fits tight and the op rod isnt binding or touching the wood
  14. T

    garand muzzle gauge

    to tim the student, sorry about RUN-ON rant at 75 yrds the grouping would fit inside of a 6 inch circle now it shoots inside of a 3 inch circle but not real tight could be stock fit and more then likely its also my trigger squeeze BTW i was using a duff gauge. and with a tighter grouping after...
  15. T

    garand muzzle gauge

    i plan on doing that but im also gonna get some gauge pins made instead of the traditional tapered type im gonna get individual ones made 3 or 4 of them.. 300,301,302 and 303 and maybe 304 i think that would give me a more accurate assesment
  16. T

    garand muzzle gauge

    a while back i took my garand to a very compitent gunsmith to have my s.a. 48 barrel re-crowned cause the muzzle had obvious uneven wear at the end. i asked if he could re crown the muzzle but retain the factory contour of the muzzle and he explained that he didnt have the proper crowning tool...
  17. T

    m1 tools

    if anyone is looking for a trigger housing break-down tool go to your local home improvement center and get a micro bar-clamp it may seem flemsy and cheap but it works like a charm as for the bolt tool, well....i just made my own out of materials i had laying around but overall,they wer dirt...
  18. T

    m1 stock

    thx greg
  19. T

    m1 stock

    hey ya'll,i may or may not be the exception to the rule,but i was able to get all that gooey crap that the army soaked the stock with.does anyone know what product to put back on the stock that will dry completely? incase your wondering i left the lower portion of the stock alone i replaced it...
  20. T

    gas cylinder lock screw m1 garand

    dfariswheel,thx for info i guess that explains the hump on the cylinder lock,if and when Z day hits ill already have the nesesary hardware in place to launch grenades minus the grenades and launcher lol you wouldnt happen to know where i could get a launcher plus a butt load of grenades ...
Back
Top