Search results for query: *

Anyone know how to get and change a h&r mainspring. The plastic piece is broken and a small chunk of it fell out when I took the grips come off :(

Purchased some coated 9mm bullets for the first time from MB and I am getting leading just after 100 rounds. I can smell the coating burning up... I'm using 4.1 TG 1.08 oal. I am not scraping any of the bullets when I seat them. Any advice ? I''ve been using xtreme till now with great...

Anyone reloads brass with a dark patina on it ?

I have an lc9 which I want to trade for either a s&w 910 or a g21 which an acquaintance has.. I like the size of the lc9 but hate that long trigger. I have a g30sf and a g23 which I really enjoy shooting... I am leaning toward the g21 but the 910 is really winking at me ;) I am a little...

I loaded some 357 mag and 44 mag with Unique. 6.0gr 158 lswc for 357 and 7.0gr 240 Keith 429430 sized at 431.... That unique residue cleaned right up of both wheel guns using some Hoppes ;)

Would you say the case support on my g23 gen 3 are pretty good ? Any suggestions on how to detect "bad brass" to avoid case had separation and a possible KB ?

...........

looking to get either a mustang 380 alum alloy frame or a sig 230. Anyone have either one of these and what positives/negatives on each ? Let's not bash the 380, OK ?

Have an lc9 and I like the way it feels in the hand but the trigger pull is long..... I mean really long. Found a sig 230 and i was thinking about getting it. Feels really good in the hand and the trigger is really nice. Made in W Germany, blued. The only think i don"t like about it is that...

Want to reload for my 10mm. Colt 1911, 175 swc. Have Unique, w231, BE. my Lyman said w231 - range 6.5 - 7.4grains, unique between 6.3 - 7.5 and BE 5.5 - 6.5... Anyone have any favorite load they're using ?

Whats your favorite load for a 1911 using 200swc ? My Lyman 45h edition has 3.5grain as the most "accurate" load. ;)

Want to get a powder check die to avoid any double / under charges. Which one works better ? Rcbs powder cop die, Rcbs powder checker or the Hornady cop die ?

I was reading an old lyman #45 manual today to check for old 38 spcl loads and came across 2 powders they used the most back then and now I guess. Bullseye and Unique... Sweet ! Bullseye is a great powder for 45acp as well :)

Anyone here tried Gunzilla ? I've been using #9 for a while now but I am willing to try different products. Trying to clean those nasty lead rings on my blue wheel guns ;)

Got this p99 magazine on ebay and I think its not the real deal. It does say megcar on it but the "made in Italy" is missing and well as the "walther" logo on the bottom. What do you guys think ? http://www.dropbox.com/sh/ungux8jikxde8wh/GX_JO2EDqJ/walther%202%20%2870%25%29

Is it true that Nickel brass life expectancy is a lot less than yellow brass ? I see the nickel brass runs more $$ than regular.

Want to reload for my g23 and can"t get over all these posts I read about kabooms with Glocks. Any advice before I start reloading ? Would a LW barrel lower the risk? Would like to use 4.5 gr 231 with some 180 gr Berrys but would like to load 155gr cast swc from MB in the near future which I...

My g23 3gen seems to have a rattle sound when I shake it up and down. Can't seem to locate the problem. If its cocked, the rattle is gone.

I would like to get some ammo boxes. i hear Dillon and MTM boxes are top notch. Do you guys recommend 100 or 50 round boxes ?

Have a uniflow which is not consistent when dispensing the charges. It varies from charge to charge. I have it set for 8.5. It delivers 8.5 once or twice and then it delivers 8.8, 8.3, 8.7.... To be fair the only powder i've tried so far is Unique. Anything i can do to rectify the problem? I am...