Search results for query: *

I had the chance to visit the NRA center musuem in Virginia this past week while visiting the grandkids in Springfield. I'll tell you right off...I haven't been an NRA member for almost 35 years. But, I was sure impressed with their collection and considering membership again. Being a disabled...

Ok. Went to the range this morning. Now my Chrony doesn't want to work. Help!!:cuss::fire::eek::banghead:

OK. Next Spring I will be having a new rifle built. Busy now putting all the parts together. I'm torn between a .243 AI or a 6mm AI. Which do you think would last the longest shooting mostly max. loads? The barrel will be the best I can afford, (probably $250-$400).

Any members own the Celestron Regal 100 F-ED spotting scope? Any opinions on it. It has a monster 100mm objective.

Based on your personal experience which riflescope do you feel has the best eye relief at either 16x or 20x? Either 1" or 30MM tube. I would like to keep the price range at $500-$800. Uhhh...Of course I'm looking for a scope that maxes out at either 16x or 20x.

Over the years the socket heads on the action screws on my BDL have gotten a little boogered-up so I have decided to replace them. Any ideas where I can purchase the 2 screws where the shipping won't cost more than the screws themselves??

Finally got my Chrony replaced so I will go out again Wed. and check some more reloads for velocity. I already did accuracy testing. My ? is...Does a clean/dirty barrel have any impact on bullet velocities. Watching football yesterday and got to thinking about this. Or maybe it doesn't...

Does partial neck sizing in anyway affect load pressures? I always neck size and just recently purchased a Bushing die and was wondering if I'm going to be able to safely shoot an old receipe with partially sized necks.

Which of these 3 cases do you think shows the correct amount of Tempilaq?

In your opinion... Is a manual Bench Rest Grade Powder Measure better than a, "regular" manual powder measure. How?:confused:

In my annealing setup I plan to use 2 torches facing each other. My question is...Since the case to be annealed will be receiving heat all around it, does it matter how fast the case is spun? My power driver has no speed control. It really doesn't speed really fast but, I think it's faster then...

Any current feedback on the Kenton Industries Trajectory Compensation Turrets??

Tried to search these bases and couldn't come up with anything, (probably not looking in the right place). Anyway, a friend mounted these bases for me quite a few years back. They are Baer bases. The front base shows markings of, front and short. The rear base merely says Baer. Very clearly the...

Just learned we have our first ever Dick's come to NM. Do they carry firearms and reloading stuff?

Any members have any user knowledge on the above mentioned electronic powdwer dispenser??

Any members have any thoughts on the Lieca 1600? I read that the 1200 was poor on snow covered ground. What about the 1600?

Mistake. Back in 1969 I was getting into reloading. I took my first reloaded rounds out to the gun range to see if they would go, "bang". The first 2 shots fired just fine. On the 3rd round I felt it kicked kinda hard and instantly felt something hot on my face. I brushed my face and saw some...

OK. Most guys seem to have a preference for big hog rifles, Well, how about a good rifle for our small Javelina out here in New Mexico. Not very big probably 30-60 lbs. I've always hunted them with a bow but, with major surgery on my shoulder this year I plan on using a rifle if I draw out. Yes...

I have a question on getting correct measurements from the bullet ogive of a loaded round. While attempting to get a, "good" reading are you supposed to take the reading as soon as the bottom of the case touches the jaw of the caliper or do you kinda have to, "snug" it up a bit and then take a...

This is probably a crazy question but, I don't know so I'm asking. What is the best way to ensure inside case neck consistency to aid in smooth seating of a bullet. I currently use Win. cases and sometimes when seating bullets some go in as smooth as could be and some seem to, "drag" a bit while...