Search results for query: *

I have a Ruger LC9 and the firing pin mushroomed. I bought all the parts and replace it. But while trying to take the rollpin out to get to it, the punch broke inside of it :cuss:. I tried to drill it out with on luck, since the punch is harden steel. Any ideas? The don't won't to send it to...

I have been having problems sizing .223 cases using Hornady's sizing die. As you can see from the picture at the end of the case it makes a ledge, but it only does it the one side of the case. Also it only does it with mil brass, ie WC, LC brass. I use Hornady's One shot case lube. I used to use...

I have made a simple reloading log for plicking etc. Let me know if I should make any changes

I just got a Hornady Case feeder a couple of days ago that I added to my Hornady LNL AP press with ezject. I'm having some problems that I'm wondering if I got a bad unit or are they nothing but problems? 1) Case hits leading edge of shell plate, the cam wire is maxed out, adjusted left pawl...

I'm having problems with reloads on .243, I'm shooting a Savage Axis Bolt action rifle and about 4 out of 10 shoots, the primer blows out causing the gun to get jammed up. I'm using Tulammo large rifle primers and varget powder, and using mid loads. I load other calibers and don't have this...

I won a Remington Nylon 66 at a raffle. I had to wait 10 days to get in (I live in CA). I decided I don't have a need for it and want to trade it, but realized, it does NOT have a serial #. I looked up the gun info and it says pre 1967 nylon 66 didn't have serial numbers, so my question is, I'm...

I am looking to buy a 40SW and looking for something with a light trigger pull under $600 and CA legal. Thanks for the help

I started reloading and was wondering if it makes a different to separate and load the same manufacturer of brass? ie, military to non, or same brands together FC with FC, Rem with Rem. I load the following caliber, 9mm, 40SW, 38 sp., 357 mag, 45LC .223, .243, and 308

I'm just wondering what press(s) everybody owns. It's multiple choice if you have more then one. I personally have a Lee Single stage and love it

Here's my story. I bought a used SW40VE from my buddy, not the best gun but it was cheap. I paid and got the tigger pull reduced from a local gunsmith. But then I had ejection problems with it, had before I got the tigger pull fixed, so I decided to send it to SW to get fixed (SW won't sell...

I just got a 5 gal bucket of old dirty brass from my buddy, whats the best my to get them looking good? Its been in the bucket for years, is it safe to reload?

I live in a small town and only have 2 places that sell powder and primers, unless I want to drive an hour away. Price here is $29 for a lb of powder and $42 for 1000 CCI small pistol primers. Is this the average price or is our town screwing us? Also, i'm going to my first gun show in Las Vegas...

OK, I have loaded 6 different loads and was wondering, in your opinion, which do you think is the best load? All loads are 9mm 115g, Remington FMJ, 1.135 OAL, light crimp, CCI primer, and mixed brass. I will be shooting them out of a Ruger SR9

Ok, I picked up 1000 rds of 9mm 125 gr. .356 truncated flatpoint lead cast bullets from bear creek today and was wondering if I can use the same reloading info for 125 gr. fmj load data. ie, powder, grain, and OAL:confused:

I will be reloading the following calibers and wanted to know which powder I have listed would be the best all around, con and pros 9mm, 38 special, 357 mag, 40, and 45 colt. The powder that covers all these calibers are listed below. I don't want to buy a bunch of different powders, just...

I'm new to forums and decided to give it a try, let me know if I'm doing something wrong. I have made the first step to starting reloading. I have been hand loading with the Lee classic kit and have decided to step in up. I have bought a new Lee single stage press, and I'm confused on which dies...