Search results for query: *

Hi Everyone, disassembled a 7600 to change a broken extractor. Expected to just change out the clip style extractor only to find that this bolt has the rivet type. I thought the 7600's were all the new style. Was just wondering if some of the early models still had the rivet type or maybe the...

Gas cylinder on a Rem 1100 came off the barrel. You can see where the solder did not take on better then half of the mounting surface. If I thin both surfaces and use a heat sink paste. Can I use 1200 degree solder without any change to the tempering of the barrel or the cylinder? Thanks

I have a problem child. A Marlin Model 57 .22 WMR. It will not eject loaded or empties at all. it extracts fine. I have changed just about everything action wise, except the shell lifter, as I cant find one. And when I do, I will try that. On the rare occasion it does clear it barley makes it...

I wonder if any of guys know anything about this gun I have It has berlin on the left side of the barrel and a name I could only make out a P. Heil and then two symbols I think. And Special Stahl on the right of the top barrel. It is a 16 ga over what I believe is a 7.62 rifle. Beautiful...

Well just finished building a closed off room with ventilation in my pole barn for a hot bluing set up. Did a few restorations prior and they came out excellent, so I decided to build a room to keep from contaminating the rest of my shop. I also refinish the stocks. Any pointers from you old...

Friend has a 7600 Gamemaster and put a set of see thru scope mounts on it. So since he couldn't bore sight down barrel he went and bought a bore sighting rig. The kind that has a spud and device that sit on the spud on the end of the barrel. You see a graph in the scope and center the cross...

Hello. I have a Marlin Mod. 444ss. When I load a round it only goes in 1/2 way then I have to force the cartridge in and it scratches and shaves brass from the shell. Can I open this port up a bit or take some off the gate? Has anyone else experienced this problem or know of a fix? Thanks. P...

Hello, this has probably been discussed already but maybe someone can give me some insight. I have an opportunity to buy a TC Contender with 4 barrels. A 45 / 410, 44 mag, super 14 7mm tcu and a 10" 7mm tcu for just under a grand. My question is: can you buy ammo for the 7mm tcu? I don't reload...

Hi, I bought a used 22 rifle that has some deep pits in it. I sanded some of the smaller ones out but it would deform the barrel too much to try this to the deep ones. What can you use to fill that will take a cold blue other then TIG welding? Is MIG to hot? Any suggestions? Thanks.

Hello, I know it is a model 37 Featherlight but they all are featherlights. Is this a field grade standard or a economy? Some of these old boys are worth a pretty penny.

Maybe I should have posted on this thread http://www.thehighroad.org/showthread.php?t=748294

Hello, I am trying to find a front sight for this rifle. I have checked all the usual places but no luck. Numerich is sold out. I am sure there is a sight out there that will fit this screw hole pattern but am having no luck finding one. I have thought of filing a dovetail into it right at the...

Does anyone know the history of what I have and what it might be worth? It is a Steyr 1918 with all matching numbers. I also have a captured enemy equipment certificate. I have attached a few photo's. Thanks

Hi, Just picked up a contender barrel in 7mm TCU. It came along with a set of three barrels I got at an auction. Don't know to much about the cartridge and I will have to do some research on it for sure. My question I have is it has no sights on it. There are tapped holes at the front and rear...

Hi, I have a lever action Marlin in .35 Rem. After the first shell is loaded, the second will load onto the carrier but it will lock up. The third round will stick out of the tube magazine just enough to keep the carrier from rising up to load, thus lock up. Once i sneek a small punch into the...

A while back I had a thread on this site why there were 8, 5, and 2 round clips. But no three round clip for a ceremonial rifle volley using a M1 Garand. We went back and forth with different ideas and why one was need in the first place. Well I finally came up with a solution. I just cut a slit...

Just bought a Marlin 783 Bolt / tube mag in .22 Magnum from a guy. I can get it to feed a round from the mag. As the bolt comes forward, it pushes the round forward. Then the tip goes up and into the very end of the chamber but the end of the case is just halfway into the bolt face. The round is...

Hello everyone, I am Looking for a bolt for a Remington Model 33 .22 cal rifle. My friend inherited it from his dad. after he passed on. Only thing is he hid the bolt so the kids wouldn't shoot it and know no one can find it. Any suggestions where to even start to look? Thanks.

I know you can make a two round clip for match shooting. I would like to know if anyone has a idea of a Three round clip for use for the three round volley for funerals. I see how the cuts are made for the two rounds and thought I could just make the cuts a little shorter to accommodate three...