Search results for query: *

Yes I realize that thank you, only range time if I end up with it. Still pondering it over. The more I think about it the more I think I could also build a caspian 1911

Correct I would hand load for it. Honestly probably why no one has bought it yet

it’s a pocket hammer chambered in 38 smokeless rimless which from my reading is also 38acp a precursor to 38 super

Yeah I have no issues negotiating, I buy From them quite a bit. I just was unsure if a gun with worn bluing would be worth 6 or 650.

My local pawn shop has a 1903 colt pocket hammer in 38acp, I’ve been looking them up but it’s difficult to find good values on them as one small thing seems to make a $500 gun worth $1500. So with that being said The pawnshop has one listed at $750 on consignment but they said he would go lower...

Can you post a picture? That sounds like it would look great! Also have you shot it much if so how do you like it? All I’ve ever seen is people put a few 100 rounds through and do a review

Thanks everyone I think I will go with the m17 safety bravo edition

I’m looking at Sig P320 M17’s I’ve narrowed it to that but should I get the manual safety version or the non safety version? I’m used to 1911’s so the safety doesn’t bother me but fondling one in the Gun shop seems like it may be in an awkward spot. Anyone shot one or both?

I think it depends a lot on were you would be surviving. Say if I some how got lost out in the woods in illinois and some how I was out there for a long time, with only what I had, I would take a 22mag because in IL there really is no dangerous game. With proper shot placement and with in close...

Well it out shoots me as I'm just starting to get into high power stuff. It will put 5 shots in just over an inch at 100 yards which normally I wouldn't brag about but almost always three of them are touching and within 1/2in. I can tell you I'm not the worlds best shot by any means but when I...

Thanks, that's what I needed to know. As they say some information is dangerous. I think I'll leave this to a smith because I don't really need to know.

Ok I have what I think is a dumb question but I would rather be safe than sorry. I have a Remington 700p that I think has a bedded stock. I would really like to find out but I honestly don't know if taking the stock off would screw up accuracy. I'm thinking I will be safe but I want to know for...

Well I finally found out the rifle is a 308, and I'm not sure about what scope it has because the rifle I saw didn't have one. So I'm going to see if I can do some digging and come up with something. Being I already have a 700P in 308 this isn't that appealing anymore. Although my 308 dose need...

Between my dad and myself we already have a 308win, a 30-06, and an M1 Garand so I liked the fact that it was 30 cal that way I dont have another size bullet laying on the shelf. Like I said before ammo cost is of little concern because I hand load and could still probably reload 300 for 50-60...

Well I know the 5r has many threads and I've read a number of them but my question is a little different I hope. Back story is a guy my dad works with is getting married therfore he is downsizing his collection. He has on consignment at a local gun store a Remington 700 5R in 300 win mag(or...

I started loading 308 with tac because that's what my dealer suggested, so I took that. My starting to mid loads were far from MOA which granted I am not the best shot and I was using cheap 150grn bulk bullets but it wasn't even close. If 3 shot groups would get into 1.5in at 100 yards I was...

Thank You everyone, I will start experementing with the other powders, I have on hand then.

I have been loading 38spl with 5.5grns of AA#5 and a magma 158 BB LSWC. This has been a VERY accurate load out of my S&W model 19, more than once I've been able to put all 6 shots with in roughly a silver dollar size area at 25yards. But the problem I'm having is there is so much soot and...

Ok sounds like I'll keep it under $125. and yes your right there is a sucker born every minute. Thats why I love going to auctions, if I dont get a good deal at least I'll get a good laugh.

I bought a set of used 30-06 dies that when received I saw the decapping rod was bent and the lock ring screw was stripped, well I called RCBS told them what I needed and also told them that this was a old set I bought used. Without a second thought they sent me everything I needed plus extra...