Search results for query: *

Does anyone remember the formula for rear sight movement?? I have a 1911, 4 inch barrel, fixed sights, that shoots 3 inches to the right at 10 yards. How many thousandths will I need to drift the rear sight to bring it on target?? Thanks in advance, Griz.

for those who load with Alliant Green Dot, how does it meter through your powder measure compared to other popular shotgun powders such as Red Dot, Unique, Titewad, Promo, etc? Thanks.

Has anyone used this combo, and if so whadda ya think? I've been thinking of getting a new powder measure for use with my single stage presses and figured that i might as well get one that I could use on the Dillons if I ever need to.

It came in yesterday morning (7-19) and I took it to the range last evening. Good feel, good ergos. Trigger in DA very heavy. Single action not bad, but still too heavy for my taste. Hopefully it will smooth out with use. I ran 150 rounds through of 124 grain NATO without a single hiccup...

Removing copper and lead fouling from your bore has always been a pain in the neck. (Some of us have an even lower opinion of it :p) I've tried them all, and settled for the "Foul Out" electro-chemical bore cleaning system...

First, let me start out by saying that I do not like lasers on guns. Having said that, I recently installed a Crimson Trace red laser on my SIG P320 "nightstand" weapon. I think most of us pretty much adhere to the belief that we would prefer not to shoot another human if it can be safely...

Let me start by saying this was done for my peronal curiosity and not by any stretch of the imagination is it a valid scientific study. Over the years, I had noticed velocity variations by changing brands of primers, I always worked up the load all cover again. I had on hand several boxes of...

I recently acquired and used some South African bullets from "Frontier Metal Products.) The ones I had were hard cast, then plated. I was told by the guy freom California at the gun show that they also make regular swaged, plated bullets. I was very pleased with both the bullets and the price...

Introduce a new progressive reloader with automatic primer pocket swager, case feed, bullet feed and primer filler built in at the factory? Dillon's 1050 comes close, but you still have to manually feed bullets and refill primer tubes.

http://www.midwayusa.com/product/523157/labradar-ballistic-velocity-doppler-radar-chronograph Anyone have experience with this unit?? Looks like it would make all other chronos totally obsolete.

does anyone have side by side comparisons of the Mr. Bullet Feeder RCBS bullet feeder GSI International bullet feeder I'm going to get one, but I'd like to see some side by side comparisons, and hear from anyone who has experience with any of them TIA

Does anyone know where I can get an easily concealed, left handed IWBr for a Ruger LC9s Pro?? TIA

A few years, 9MM barrels for the CZ 52, and .380 barrels for the Makarov were commonly available. Does anyone know if they're still available?? TIA

Probably the cheapest insurance you can buy, and IMNSHO, the most important tool on your reloading bench is a set of scale check weights. These are precision measured little weights that allow you to PRECISELY determine and/or calibrate your scale, at the weight of the powder charge you will...

I know this has been said a thousand times before, but it needs to be said regualrly and often. "]LEAD IS TOXIC] Wear rubber gloves, such as latex surgical gloves when casting, resizing bullets, loading, and any other time that yourbare skin could be exposed. Lead build up in the blood...

Thinking of getting one, but need to know any quirks about reloading for it. :banghead: Thanks in advance. :)

As we know Powder is scarce and expensive. I recently had the opportunity to obtain two newly manufactured 8 lb kegs of Green Dot at a good price. (Actually, a VERY good price :) ) I load a lot of 9MM, .38 Special, and .40 S&W ammo, and I'm having a devil of a time :evil: finding good...

Anyone know of a good gunsmith that has a lot of experience with the old "Smellies?"

Does anyone know where to find bolt heads for .303 SMLE rifles?:confused: TIA:)

What's the deal with Arsenal USA?:confused: Every website I go to, shows all of their rifles discontinued!:eek: Have they gone "belly up?":banghead: