As the last of this springs projects, ordered a Bell and Carlson stock made specifically for this rifle with heavy barrel and detachable mags. The rifle has been sitting quite some time as was having difficulty making it fit with limited scope mounting options putting scope too high and...
Anyone tried or are using these bullets in 45 acp? Any loads or experiences sincerely appreciated.
https://www.grafs.com/retail/catalog/product/productId/75780
Anyone try one for quickly clearing outdoor range of brass? Not turning it into a vacuum, but simply blowing the brass off to side to be picked up? Thanks
After buying the inside/outside chamferers for the case prep center and the replacement cutterheads for the case trimmers, got to try them out. While expensive, definitley worth it for my purposes.
The chamferers (or whatever they are called) were alot easier than the standard steel...
Now that Tula 7.62N primers are available, what is the easiest way to remove the primer crimp from the case? Has anyone modified a swage punch? Looking for adaptation to do lots of cases, not a couple with a pen knife.
Thanks
Picked up NIB 257 Roberts Micro last week. Am waiting for scope bases, rings and a modified case (to check COL), but wondering if anyone has any specific experience with this rifle they could share, or handloading for it in 257 Roberts. Already had the dies, brass and bullets from previous...
Am thinking on new AR, and trying to choose between a RRA 20 in Varmint (bull barrel) or the RRA ATH (18 in heavy barrel) carbine. Am going to mount scope, not worried about open sights. Am interested in 100-300 yards targets and quick sight recovery and being able to see hits instantly through...
Starting to load for and dial in a 270 wby . Weighed the fed brass and it was bout 30 grains heavier than the Norma brass. Has anyone done any direct compariosn of velocity with same charge between the 2 makes of brass? Took notice Speer's manual uses the Fed brass for 257 and 270 wby, and...
Stopped by local sports shop, after discoveriong range was used for the day by hunters ed. Saw interesting revolver in 32 mag, and bought it because like the 32 mag. Seemed well made and used very little. Anyone shoot one of these or handload for one? Never even seen one before. Any good or...
Am starting to load for this rifle/cartridge and could use some hints.
1-The COL needs to close to max for easier loading into the fixed mag?
2-Also having trouble with blunt (round nosed or fp 30-30 type) bullets. Seems difficult to load mag with anything other than spitzers?
3-Unless...
Am starting out loading for the 30 carbine , so bought a Lee fc die. Couldn't get it adjusted down far enough to actually put a crimp on? Bought another one, same problem. Anyone else experience this? Trimmed all the brass down to recommended minimum lenght 1.280. Have used alot of other...
Does anyone know of a current source for Berdan primers that would fit a 308 case? Can someone tell me the correct size for 308? Thanks, have been searching internet, without any success.:banghead:
Does anyone have any experience with Houge's overmolded stocks for regular hunting rifles? Believe they come with aluminum bedding blocks and are free floated?
Thanks much
When the various loading manuals are worked up, do they use a brand new case for each loading? Do they do any sizing (partial, full length, neck)? Anyone know for sure?
Does anyone have any experience loading this bullet for handgun or rifle ? Tried some yesterday, couldn't get much expansion till about 1100 fps. Admittly firing into damp sandy/loam. Any thoughts on using it as a short range deer load?
Anyone seen a 7 1/2 in 44 special in shops near you, and what the seller was asking for it? Ones in like new condition, but fired and with box.
Anyone own one of these and have slugged the cylinders and barrel? Any known or common problems with them?
Thanks.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.