Search results for query: *

Need a new seal for my beloved LPM-1 single stroke pneumatic match pistol. The gun is out of production; I bought it new in 1996. The part is # 2486687 and also 2506882 and 2600005. In the schematic they are labeled parts 43 and 44. Thanks.

Apropos of Tuner's magazine dissertations, I went home and looked at the 5 mags that came with the 1917 "Black Army" in my safe. They are two-toned,blue lower half and white upper half. All have very gradual shaped lips. Sorry, didn't check markings. Are these worth anything?

I can't see well enough anymore for bullseye shooting. I'm thinking of a red dot sight for my Smith 41 for conventional bullseye match. I know nothing about them. Anyone have advice and recommendations? Size of dot?

a buddy moved into a smaller place and had to get rid of his excess reloading supplies, including some he'd inherited from his dad. There was lots of IMR 4895, 4064, W748, and Unique. Some of the IMR cans had price stickers still in them: $6.95!! I poured samples from each into a bowl. The...

This was a 1948 Winchester 52B I found in a local shop.The stock had been crudely shortened and the barrel band was missing, and there was a crack at the wrist. The finish was all gone. The metal was heavily pitted and missing much of the blue. In the bore, there was a circumferential pit...

http://www.military.com/NewsContent/0,13319,143790,00.html?ESRC=navy.nl

How do you "time" a screw so that it comes to a stop with the slot parallel to the bore? I have a set of Dave Talley swivel bases to mount on my Model 52B project rifle. The heads are cylindrical and extra deep so metal can be filed off the top to make them come out flush. The heads are...

interesting piece from Military.com. A real shame this serviceman had to spend upwards of $700 to get a serviceable weapon, but I'd do it in his place. Wish I'd known, I would have sent it to him and done without beer for a few weeks. http://kitup.military.com/?ESRC=navy.nl

what's this? Arsenal rework mark?

A couple of years ago I found a beat up Model 52B. It had apparently been in a fire, because the metal was pitted and the bluing was discolored and blotchy. The stock must have been a replacement if it had been in a fire; it was crudely shortened, unfinished, and had a crack near at the bolt...

just got mine for my G22. Found that it absoutely will not feed my handloads, choking on 50% of them. They seem to jam by being cut by the bottom edge of the chamber mouth, just above the groove. Same loadds feed flawlessly in the factory barrel, and commercial loads feed fine in the KKM. So...

Clay birds are in short supply around here for some reason. Anyone know a good source? I have three or four folks who could pitch in for a group buy. There is nowhere to get clays within 90 minutes of here in central NH.

I mentioned this phenomenon awhile back. I test my handloads with 8-round clips instead of 5 or 10 round groups. I've gotten a few handloads to group nicely into 1 1/2 to 2 inches at 100 yds, which is approaching the limits of my aging eyes. But some of the best loads consistently throw the...

Hey, what was the answer to that question awhile back about which one or two parts would fully disable an M1 if they failed? Never did hear.

I have a MEC 600 Jr Mark V. My shotgun is a 1931 Fox Sterlingworth with a 2 5/8" chamber. I'd like to load that length or 2 1/2". Are ther adapters to convert this press, or home-made rigs to do it?

The "Get Loaded" sale, 500 or 1000 free bullets with purchase of a press: http://www.midsouthshooterssupply.com/hornady_get_loaded.asp Looks like some good deals for thos who wish to get into reloading.

Noticing an interesting phenomenon. I shoot 8-rd groups at 100 yd to test handloads, and I'm getting some really nice groups, but often the first round of a clip will impact low and left, with the other seven going all together, often in one ragged hole. So I tried a clip of an earlier...

Have a nice piece of black walnut I want to use for my Win. 52-B which has a butchered stock. I have it rough-cut to shape, but I can't find any good instructions for inletting the barreled action. Any tips?

pardon me if this has been beaten to death here already. I shoot a 10 meter air pistol match every Thursday in a friend's barn. It's great fun and very challenging. I shoot a Steyr LP10. Any air pistol match shooters here? When I shot club matches with .22 and .45 in Ohio I asked one of the...

Got some of their 158 gr JHP ammo. Was able to fire two cylinders before giving up. Primer metal flowed into the firing pin hole, locking up the cylinder. They average 1336 fps and are actually comfortable to shoot. Gold Dot bullets. I'll go back to my handload, 10.4 gr Accurate #5 with a...