A good deal on an AK63D came my way. I jumped.
Not mine, just an image.
I already reload for several calibers.
With x39 surplus selling for .20-.40 in Bulk, I started thinking about reloading.
If you reload for this caliber:
Where are you sourcing your brass?
Favorite Powder...
I bought a Springfield 1903 about 10 years ago at a gun-show.
The receiver has been drilled and tapped for a scope. I don't think it came from the factory this way.
The date stamped on the barrel is Oct/1918.
Couple questions:
Is it possible to add a "peep" type rear sight?
The receiver...
Evening all,
I'm looking for suggestions/recommendations on a Traditionally mounted .308 Scope with a BDC or Mil-Dot reticle for a Ruger Gunsite .308.
I'll be using an XS picatinny rail.
Any and all input/suggestions or critique appreciated. Pics of your setup appreciated. Even if you...
Evening All,
I ordered some Speer 170gr SPFN bullets for my Marlin 336.
I got to wondering, can these bullets be loaded for my .308 Win rifles?
This particular bullet isn't listed in the Speer 14 for .308 Win, only 30-30 Win.
Can the bullet construction handle the increased powder...
I've been loading a fair amount of 5.56.
At some point, I decided to clean the resize die. I failed to reorient the die correctly and then resized/processed/and loaded approximately 500-700 rounds of ammo that will not chamber.
The die body wasn't wasn't set deep enough. :uhoh:
My...
A question I've been pondering.
Maybe I'm over thinking it....
I found an accurate load at the very bottom of the Min/Max charge scale.
Can I expect a Soft Point, 5.56 round to mushroom and perform terminally at roughly 2200 FPS?
I can raise the charge, at the cost of accuracy...
Are there any Zen-Full folks with words of wisdom. Or at least people with links? :what:
My Hornady LNL-AP is giving me fits.
Last night, I was reloading some 9mm and at first, I had problems with the shell plate advancing far enough to allow the spent primer to drop... Give it a "wiggle"...
I'm shooting a new model Ranch Rifle. 582 Series.
I've shot Federal 5.56 and American Eagle .223.
I cant get through any Factory Ruger Magazine, 5 round/20 round without a failure to extract.
AFAIK, there has been less than 200 rounds through this rifle.
The pic isn't mine, but this...
Anyone here load for their Mini 14/Ranch Rifle?
1:9 twist, 582 series
I'm gearing up to give it a go with some CCI 41, some IMR 4064 and most likely a 55 gr HPBT to start.
I'm Interested in what worked best for y'all, if you feel like sharing.
Thanks
PS, I posted this same...
I ordered a RCBS X Die, .308 Haven't received it yet.
I plan on using it for my M1A. I'm hoping that it will increase case life.
Any opinions, thoughts, or input???
Thanks :)
I've been loading for my Rem 700 in .308 and I'm getting about 1-2 MOA.
The free bore measures out to 2.955"
From what I've learned, .020" off the lands will give better accuracy. With such a long free-bore, this isn't possible.
My questions: What is the longest COAL anyone here has...
My question is: When switching between calibers, do other LNL AP users need to make pawl adjustments?
I reload and shoot mostly 357 Mag and 45 ACP. Whenever I switch-out between the two, adjustments are necessary for smooth operation.
Is this common, or have I just not found the "Sweet...
I just cast my first .38 cal boolits ever last night. All went well. I shot a couple hundred today and am very happy.
Now I want to cast for .30 cal rifle with a gas check.
My Question: I am looking for a .311 dia bullet. Is there a way to use a .309 mold and a the Lee .311 Sizer Lube Kit to...
Hello, I have question.
I shoot Speer 158 gr SWCHP over 6 grains of Unique in .357 cases. I'm happy with the load.
What is the danger of putting that same amount of powder in a .38 case?
My Speer manual lists 5.2 as max for .38+P
Every once in a while, when shooting from a LCR, the...
Anyone have information about 165 gr RNFP Cast Bullet, plain base, over Unique in 30-06?
I bought some Missouri bullet .309s for my Marlin 336 Micro Groove. I need .311s and am considering loading these up in my Springfield 30-06. The Powder I have on hand is Unique.
Any information...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.