Search results for query: *

WLR'S Rem's 9 1/2 I've been reloading for 30 years and last couple years Winchester brass that I've bought has been a little less than great let's say NOT ALL OF IT BUT SOME.

opened a new bag of 50 45-70 Winchester cases the other nite and out of 50 3 the primer pockets are to large, so checked them with a different primer brand REM nope they fell out too! even new cases can get you ! lucky I've only got one more bag of that lot.

compression is a thing that you really need to (FIDGET)with!! in a case and it it is not meaningless anybody knows this that has any know how, how to load BPRC. Playing with the burn rate is how to tune your load by burn rate is just one way to tune your loads. How you stack your and powder...

old #39 dose have a point there you do need the rifle and be able to shoot that well to tell the difference. But other then that he is being a jerk ABOUT IT AND MAD AND THAT HE FELT NOBODY WAS LISTENING TO HIM!! I guess I'll be in trouble for this one! OH WELL'

Bingo !!!

STEEL HORSE RIGHT NOW there is a kik promoter on a few other sites and black net seems to be promoting Swiss this is not new on the NET as far as trying to sell there product. There are others doing this in all products sneeking around on forms! THINK ABOUT THIS UN-SURE AND SWAY !!!

Hey everybody is going to sell you a line of %$#*! you think you need a faster burn rate in your pan then just grind your 4F little bit it's pan powder!

The Lyman kits are are a piece of cake, but I see your sitting on the fence so !! .just go buy one. NO kit just snaps together.

TREBLIG NOT always your trajectory is a rainbow 500gr at 1300 fps if your zeroed at 100 yd at 500 there is about 290" bullet drop then there's windage so at that point 50 fps wont make you or break you. Controlling your fouling is a big ticket item. shooting long range with BPRC fouling is...

Yes there are a few long range top shooters in BPCR that still use Goex. I did do a comparison over the crony few years ago and with Goex,Swiss,kik,and diamond back powders and all those notes are lost. The rifle used was Shiloh Sharps 40-65 R L chambered 32" barrel 400 gr bullet. ALL the...

Let me see! not worth much? We will offer nothing to a friend " (WORN RIFLING ON A MUZZLE LOADER)? You want to bore it out to a .54 to a smoothbore ! AND you would have A 20 GA muzzle loader with rifle sights? some what! I would bore it to correct dia for 20 ga.

Without !! SCOPE kinda like selling a car with custom rims that cost 1000.00 and you will only get 300.00 more but it will sell a faster.

full sizing die is primary die and neck sizing die is secondary. Neck sizing is the way to go for accuracy and case life but if you can't afford to put the extra $ to have both, than get full sizing die because you can adjust it to almost do what a neck sizing die can do.

Goex has softer fouling than Swiss.Swiss has more energy per grain,but Goex likes more compression than Swiss, so more grains per load to gain your energy on Swiss, But Swiss will still end up top for velocity and harder to control fouling, so more blow tubing,grease cookie or one more grease...

soap and water and any non petroleum oil (petroleum oils and black don't mix) I will use Kroil oil to lift any leading but clean that out with electro clean and use soy oil to protect.

common sense ? and common sense !!!! NOT ANGRY HERE. There are some that need have there screwdriver taken away from them!! I'm sorry.

this will add it up! some people should not own a screwdriver!!! and some of these posts. I just go back to it's never funny until somebody gets hurt!! I'm sorry not PC!! THEY cant think on there own feet THEY JUST go to the key board until they see what they want. THEY think that load will...

Load meno's are per gun because no such load is the same in the same cal gun so you are back to ground zero for the next gun and been doing this for 30+years so I have A GOOD load map in my head. JUST get yourself a binder and add pages as needed.

YES NOW read it 3 times over and then ask ? not being a jerk here but read it and then ask !!

AND SOME should never own a screw driver