I used Warne high rings to mount the Weaver Tactical Grand Slam 3-10x40.
http://www.midwayusa.com/product/398781/warne-permanent-attachable-ring-mounts-cz-527-16mm-dovetail
I considered modifying the bolt in order to go lower, but the current scope height fits my cheek weld just perfect as it is.
I too, have the BDC on a .308 and I love it.
The rimfire model is at the top of my wishlist. Great glass, useful reticle, affordable price, whats not to like?
I have shot various Prvi loads in both 30.06 and .308. It functioned fine, but POI was always lower than that of other loads I was using.
I think the Prvi powder charges are pretty tame.
I HIGHLY recommend the CZ 527 which now comes in left hand models.
http://www.cz-usa.com/products/by-category/rifles/
I have the Varmint version and I love it. All 527s have a "micro" action that is built around the .223 cartridge for a very short receiver, a fast bolt throw, and overall trim...
In these pictures you can view from directly above and directly below to see just how much material I took off.
As far as mounting the scope rings, my only choices now are the very front and very rear slots - which is fine since those are the only ones I used previously.
The mount has since...
follow up
Well, I loosened the loctite and took the mount off the gun and put it on the bench grinder.
In the attached picture you can see the freshly ground surfaces. Its a bit hard to tell from the angle of the picture, but the cuts are angled at about 45 degrees so that a shell ejecting...
Install one of these on your current 1100. Its a standard part for the Competition and Tactical models of the 1100.
http://www.midwayusa.com/viewProduct/default.aspx?productNumber=185213
I hate to admit it, but I think I will just use a bench grinder to modify my mount.
Good idea regarding the bottom of the scope ring. I could shave some of that, too.
M1key, I may do what you did. As you can see in the attached pictures (a view from the side and a view through the magwell), the empty cases are impacting the bottom of the scope mount. I think I can grind the mount to an angle in that area so that it helps to "kick" the cases to the side and...
I have an adjustable gas valve that I bought so I can shoot the Hornady 155gr A-Max.
Would you recommend increasing the speed of the oprod in order to make the ejections more forceful?
This malfunction has happened with a couple of types of ammo.
My M1A has a an occasional problem that causes both a FTE and a FTF.
As the ejecting case is flying out, it is getting caught by the operating rod and slammed up against the bottom of the front scope ring. This causes the spent case to be jammed in between the operating rod and the scope ring...
Which brands do you guys use? I have shot a couple of shotgun stages and always borrowed a belt and carriers from a squadmate, but I would like to get my own setup.
What are the quality options available?
For the OP, I would agree with all the consensus that there is no reason to shoot 6.8 instead of 5.56/.223 in a 3 gun match.
Regarding sargents1 experiences, I too have used a Mini 14 in a match and I was pleasantly surprised that I wasn't blown away by the ARs. Half our shooting is between...
I have a little experience with ARs and a LOT of experience with Mini 14s.
As previously stated, the new Mini 14s are a step up in terms of quality and accuracy. A friend has a new one that is really nice. 2 moa is a piece of cake.
I have a mid 90s mini that actually shoots well. With a...
The DNZs are a great mounting system. Strong, simple, and somewhat lightweight - what is not to like?
A friend and I both have a set of DNZs and they have been excellent.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.