Search results for query: *

hmm thanks for the replies guys, I think i will purchase them, I will eventually be reloading for my AR, mostly mass ammounts for plinking etc not all of them will be benchrest loads. So from what the above poster stated, are they harder like a military primer?? they are CCI Magnum Small...

what is the differnce between Magnum small rifle primers and small rifle primers? Can you use them [the magnums] for reloading 223??

Thanks for the help guys, I just wanted to be on the safe side, The Nosler Manual is kinda hard to understand I think when they wont give you a Min COAL just a max. I get they are trying to help you with the most accurate load but for a newbie case density isnt helping me with MIN COAL lol

this is what I was concerned with, the load I posted above fills the case all the way up to the about the middle of the shoulder I would guess and the bullet is compressing the load So I was concerned abou it, But the Nosler Manual says you can go all the way up to 50 grains with this stuff I...

Quick question about COL, when I load 9mm I just pick a length between the MIN COL and the MAX COL, Usually one that will load good in my pistol. The Nosler Manual does not list Min COL only load densities or some crap I didnt understand it very well aside from the fact that the more full your...

hey guys im at my wits end trying to figure out the correct combo while reloading .308. basically this is what I have. Powder IMR 4350 H 4350 Bullets Barnes 165 GR XBT Hornady 150 GR GMX could some one point me in the right direction for a good load on either of these combos. I have...

whats so good about using a hand press vs. the priming function on your press?

I beleve Evan from On Point Firearms is a member here on this board.

this show has been around a year or two. I think i saw some of the first season, they had 3 groups of people usually about 2-3 per group. one Father/daughter group who went Moose hunting with a guide but never killed one, they did get a shot at one but missed I would assume they flinched/jerked...

i bet Bill is rolling over in his grave:D Really though, why WOULDNT Ruger get into the AR game? Remington has a line, S&W has one to, Winchester.. well they are under FN's umbrella. Im not a huge fan of modern day Ruger's but they are just trying to compete in the firearms market and they...

8mm Brass bore brush fits excellent in the chamber of the 74. I had a problem like this with my tantal, a couple trips to the range, along with cleaning the hell out of my chamber(not the bore) with the 8mm brass bore brush. Rifle fires like a champ now and has not jammed once.

thanks alot guys, I had not heard many bad things about the press aside from primer issues, and one about powder leaking from the disk. Just seems like once i started loading the problems started buidling up lol Ive had the shell plate off a couple times etc etc!

I just started reloading after kicking the idea around for years lol. Im using a Lee Loadmaster with a bunch of problems. When i first sit it up I deprimmed a bunch of brass and ran them threw the cycle, the first thing I noticed was the case feeder would not fully load a case into the shell...

I figured it was to light a load, I had checked a book, and must have misread the load charge. I loaded up about 20 of these as my first reloads to get the hang of it. Guess i need to go buy a bullet puller lol.. Also, I have a question about COL, as long as you stay within the minimum COL...

how does this sound for a general target round out of my G19. Bullet- 115 FMJ Powder- Accurate No 7, 6.6 grains Once fired brass mixed head stamps. Federal No. 100 Small pistol pimers. COL-1.104 this sound like a good target load? or should I tweak it...

Gun broker would be your best bet, they are not cheap by any means and usually run past the $3k mark. good luck!

dont use a shoulder holster if you are worried about it.

i think thats about they only way you can rank them is fit and finish! they are all built to a certain spec. My 64 East German Mak is nicer in fit and finish, machine work than my 1990's Commercial Bulgarian Makarov. but other than that they are pretty much the exact gun. i would expect...

East German on top Arsenal Makarov on bottom i really want a military Bulgarian, a civilian russian, the polish and chinease one to keep these two company!:D

:confused: The Israeli's didnt make the Maadi the Egyptians did. you might be thinking of the Galil