Search results for query: *

I have a .308 mold that drop 160gr bullets. I want to load some of these in my fr-8 Mauser. I have some Reloader 7, 3031, and a little but of 2400 on hand. They will be gas checked, and cast with wheel weights. Not looking for super light gallery loads, but I would like them to be hot...

I recently bought a RRA 9mm upper for my AR. The rifle has functioned normally through sever hundred round before the upper swap. In 9mm configuration I basically have a single shot. The rifle will fire, ejects, and loads a fresh round, but the hammer follows the bolt forward. I have the...

Steel can be reloaded. I have been doing it for years. There are a few caveats however. - .223 is the only steel case I have found that uses standard boxer primers - you can't use lacquered cases - you can only reuse them once - the steel is a little harder to size and may accelerate...

Im near Columbia SC and wondering where to get my SBR engraved. I would really rather not walk into Things Remembered with a "bushmaster assault rifle" lol Anyone know of a place around here that does laser engraving and is farmiliar with firearms?

my normal powders were sold out today so I picked up an LB or Hodgdon Superformance. I have used Superformance loaded ammo in .308 and .223 so I figured I would give it a try. I found out a little too late, that the powder is not the same as used in their loaded ammo and load data is only...

Christmas money is burning a hole into pocket and I want to finish a .300BLK upper for my SBR registered lower. I'm looking for a reasonably priced barrel between 9 ad 10.5 inches that's in stock. I would like to spend around $150ish. I do t need anything special, it's just gonna be a...

So, I got some mail from the BATF today. I literally ran inside and ripped it open. I mailed my SBR form in June. I was disappointed to find, not my tax stamp, but a request for corrections. ARG. Apparently it is no longer kosher to register an AR lower caliber as "multi" My question is...

I HAVE to find these grips...but no luck. My Ghost Inox is begging for a set but i can only find the black version. Any help? Thanks.

I'm thinking about building a .300blk upper for my SBR reg. Lower. I really want the 11.5 a2 look but can't seem to find a barrel assembly like that in .300. Any help?

I had some wet .357 that I wanted to dry quickly before I droped them in the tumbler. Stuck em in the oven for 10 min....totally forgot about em for an hour at 325. Are the safe to use?? Thanks

I have been having trouble with my 9mm and .308 rounds. The .308's are being fired in an ar-10. When the slide or bolt closes on the round it gets stuck about 1/16th out of battery. It locks up and I have to pound it open. I am resizing all the way Down to the shell holder...past...

My brand new Pro series Smith has a smooth light break, but the takeup is terribly and gritty....sounds like crunching up a potato chip!! I think I have tracked it down to the safety plunger. I want to take the plunger out and polish it and the hole it fits into. I'm just wondering if I can...

-------------------------------------------------------------------------------- I work for a company that builds top notch power lifting and strongman equipment. I was watching a 3-gun match the other day and seeing the tricked out Saigas and Ar's got me thinking. I remember Hornady and The...

Having problems with a new-to-me Desert Eagle. The slide lock activates after every shot. It feeds and functions fine if I hold the slide lock down with my left thumb. I have tried shifting my grip and let others shoot it...I'm not inadvertently activating it. Before I order a new slide...

I have a Tex Shoemaker & Sons PC Hugger holster. I love everything about it except for the outdated black basket weave. Can anyone point me in the direction of a holster like this, in a more up to date finish. Thanks http://www.texshoemaker.com/PC-Hugger-Holster-PC.htm

Help! I can't decide between the Beretta px4 and the XDm5.25. The Beretta is alot cheaper, and I love my 9mm px4, but the Xd has killer sites and all the gear. Any input? Thanks

I have recently built a neat Mauser based scout rifle. I am using a 184 gr fp bullet mold. Very accurate and hard hitting with a gas check and a charge of 38gr of 3031. My nephew wants to shoot it. I would like to work up a reduced load for him. I have some 3031, aa1680, and 2400 on hand...

I am in the process of putting together a heavy barreled ar-15 for target shooting off the bench. I dont want to spend a ton on a scope, but I dont want to get junk either. Im looking for something that will hold zero (obviously), CLEAR, 16+ magnification ,target turrets and a 30mm tube would be...

Im thinking of adding a varmint style Ar to my collection just for target shooting and plinking. Sportsmans Warehouse has the Bushmaster Varmint Special stainless for just over $1k or I could buy this lower build kit and a Receiver from Palmetto State...

Looking for a no frills, quiet .223 can for my 16in AR. Not really concerned about weight, construction material, or fancy QD devices. Only really concerned with the most DB reduction for the least amount of money. I have done a little research and it looks like the YHM Phantom or the SRT...