Search results for query: *

  1. C

    Touching up my oops...

    Hey OP! I probably would leave it alone. But if you can't leave it alone, I would use a bluing pen, make sure you really clean and degrease the area. it helps to warm the area up also, with a heat gun or even a BIC lighter. Next time you try to remove loctied sccrews, try a solder pen or even...
  2. C

    AR 15 style pistols and vertical foregrips

    theohazard, can you clarify something. I understand 26", is that witg the brace fully extended or with it collapsed to its shortest position?
  3. C

    AR 15 style pistols and vertical foregrips

    I'm sorry, I meant to say, brace.
  4. C

    AR 15 style pistols and vertical foregrips

    so if i have an AR pistol that measures 27" from the muzzle crown to the stock when stock is collapsed the the shortest position, it is legal to pt a vertical foregrip?
  5. C

    My Police Gun

    Boy, I thought my 18.5" M590a was heavy...
  6. C

    I hate my Magpul Front Sight so...

    Daniel Defense, but it is not foldable.
  7. C

    School me on some carry handles.

    Be careful of removing the bridge between mouting points, most picatinny rails are sharp and I envision you slicing your fingers if you go that route.
  8. C

    School me on some carry handles.

    I was in the same boat as you. I wanted a good carry handle sight for a basic AR carbine. After reading some reviews and doing some research I went with an Aero precision handle. The PSA was out of stock at the time I ordered. I'll cut and paste my comments from the thread I started abot it...
  9. C

    Ithaca 37 Defense model

    Take the recoil pad off using a phillips screwdriver oiled up as not to destroy the rubber around the holes. Look inside and see if its a socket head bolt or a flat screw head bolt. Use a long screwdriver or socket with extension to reove the stock bolt and stock.
  10. C

    Is this another model 12?

    Really looks close to the m12 i restocked or the m97 wrist i repaired. I don't have my m12 in front of me.
  11. C

    Rolling Block Project

    Looks great! Very nice work, you can tell a lot of time and care went into that.
  12. C

    Marmots, 17 HMR, 50 yards, ethical?

    I shot a fox with a .17HMr once, at about 100 yards, it dropped it right where it stood, and it was a big fox too. Ive shot plenty of rabbits with one, never had one get away. I think you are okay with your setup.
  13. C

    Another yardsale score!

    This weekend was a big weekend for yardsaling, in my hometown. Digging through the boxes marked "free", at an estate sale, I stumbled on 2, Case XX kitchen knives. One is Model CAP321, and 8" butcher knife with full tang and right hand finger-grooves. The other is CAP200, an 8" chefs knife...
  14. C

    Looking for a cheap GI A2/A3 carry handle.

    I did receive the fixed stock and have it installed on the rifle. I also had ordered a extended butt-pad, the PRS, .80". When you remove the original, .25", and add the extended version, you gain about 1/2". This give a LOP of about 12, 3/4" inches, which works great for me. I am a smaller guy...
  15. C

    big barrel = ginormous scope?

    I think your scope ought to tailored to your shooting style and distance. a long "varmint barrel" is about gaining velocity. People mistakenl believe that long heavy barrel = high velocity+stiffness. Reality is, a short heavy barrel is just as stiff as a long heavy barrel, maybe stiffer. So, if...
  16. C

    Looking for a cheap GI A2/A3 carry handle.

    I would have ordered from PSA but they were out of stock for the past 3 or 4 weeks, thats why I went with the Aero product, which certainly appears to be mil-spec.
  17. C

    Looking for a cheap GI A2/A3 carry handle.

    MixedNuts, you are right, it work better if you are carrying it in a relaxed manner. Maybe back and forth to the targets, around camp, in and out of the canoe, etc. If I try to jam my whole hand in there, my knuckles will get stuck. I went and function tested the rifle yesterday, only 60 rounds...
  18. C

    Looking for a cheap GI A2/A3 carry handle.

    I have small hands. It works as a carry handle for me, if I am carrying it by the outer-most 2 phalanges, or segments of the 4 fingers on either hand. As well as I can measure with a tape measure, the opening is apprx. 11/16"x4-3/8" and is the same width, (not tapered) the whole length of...
  19. C

    Looking for a cheap GI A2/A3 carry handle.

    Got the sitgh yesterday and installed it on my rifle. It looks great! dark blackish-grey anodizing, captive attachment screws, positive click adjustment. the larger aperture is marked 0-2. There is a square forge mark whcih I believe is for BAFE ( Brass aluminum forging enterprise). IDk if it is...
  20. C

    Looking for a cheap GI A2/A3 carry handle.

    Well I went with the Aero sight. It should be here in a few more days.
Back
Top