Search results for query: *

Bullet vs barrel and designations by Paul Harrell. Your question is answered in the first 5 minutes

The installation of a Timney trigger is simple with just a little patience. The lock screws are where the patience is needed. I've installed many Timney triggers and the problem can be that there's threads on the side of the housing and might want to cross thread. Just keep in mind that no...

I've seen it with my own eyes. In early November the lot was covered with bulldozers and earth movers. Went by there after I was told by someone with the company that had the HVAC contract that it was on hold and they were paid for work done in planning, and the lot looks like a ghost town. All...

The Arkansas plant is on hold or dead. A few days after the election was called, all work was stopped and all contractors paid off for work done.

As an FFL would you transfer a gun to the buyer if there's no response within the 3 days?

https://www.atf.gov/firearms/atf-form-4473-firearms-transaction-record-revisions (Location of the revisions) There is no revision on the denial or approval process. And it does fall under an FBI header, so there is that.

FBI.gov

I'm not and never have, but it doesn't keep me from knowing that it's a fact, without a denial within 3 business days the FFL is authorized to transfer a gun to a buyer. Are you of a different opinion?

Again you are confirming exactly what I said from the very beginning, only you write several paragraphs to say what i did with one sentence. Without denial within 3 days, the sale is approved by default. You can color it any way you want, it's still a horse.

I know how to read, been doing it for sometime now. You say the dealer is required to record the response. What if there is no response? If the FFL transfers the firearm, the FFL must mark “No resolution was provided within three business days” on line 21d of the ATF Form 4473. It's easy...

It's absolutely is true. After 3 days without a denial, is the same as approval as far as the FFL is concerned. I've been there and done that on a few occasions before I got my CCL. Now it's closer to 3 minutes instead of 3 days. Besides, you basically said the same thing i did , but went way...

In Arkansas, if the background check isn't denied within 3 days, you're cleared by default.

Carrying is like wearing a seatbelt. You can wear it your whole life and never need it. The first time you don't, you're flying through the windshield.

Unless it's a custom barrel ARs are generally over gassed so manufacturers don't get thousands of calls from people using the cheapest ammo money can buy. If it's short on gas the gas block is probably out of line, but I would check to make sure the bolt catch is working properly. Does it work...

I had the problem of the slider coming up short. I loosened the two screws that hold the slide rail and the problem went away. Loosened the screws until the rail would move, then tighten just enough to stop movement. The screws on mine were so tight it was pinching the slider between the rail...

Are the takedown and pivot pins hard to get out? I had one that I tried to put put a Franklin trigger in. The trigger would go in but the selector was locked up. After three tries I put it in one of my extra lowers I had and it worked perfect. Back in the Ruger, locked up. The takedown and...

Speaking of Lee. On another site there was a comment by John Lee or somebody representing his name, on the problem of nicked brass not going into the shell holder. The fix for now on present version of shell holder is to remove the detent so the shell holder can rotate. There will be a new...

The instructions say rimless bottlenecks not recommended. I saw a video of 308s being resized without any problems. Maybe the thicker base makes it possible, but i tried 223 just because i can and got very poor results regardless of any lube I tried. As far as straight wall brass, its a piece of...

It hasn't twisted as far as I can tell, but if it does, I have a cure for that.

It's the lee case feeder #90242 and #90667 collator bowl. That's what is recommended on instruction sheet. For 9mm I put a washer the same diameter as a penny in the center to make cases feed base down. Not one upside down case as of yet. A 1/4 bolt or screw will hold it in place even though...