Search results for query: *

I am looking for +P loads for 9mm. I can't seem to find any load data. Can someone point me to some data or share your loads. I am currently loading normal loads using Univ Clays 4.8 gr using a 124 gr Rem JHP. The load chronos about 1050 from a 3" barreled Kahr PM9. I am not sure what I can...

I was shopping at the mall yesterday and went into Men's Warehouse to find some new dress slacks. (I think my gut is getting bigger). Anyway, I was talking to the gentleman about pant sizes and all of a sudden he lifts my shirt to measure my waist exposing my Kahr PM9 hanging in an OWB holster...

I am loading 9mm using RCBS taper crimp die seperately from the seating die. The round seems to stick in the die when you try to back it out. I haven't seen this with other calibers I load. If I push the uncrimped round in the die by hand, I can feel the brass kinda 'stick' and it takes some...

I ordered two new handguns a while ago from my local gunshop and they came in today. I was going to pick them both up but my ffl said that per federal law I can only take posession of one handgun per 5 business days per ffl. Since when? dave. P.S. I found my answer at the batf web site...

I found this CCW comparison chart. I is kinda handy to give side-by-side comparison of some common guns and their specs. http://www.chuckhawks.com/concealed_gun_chart.htm d.

I just bought a new Kahr PM9 from gunbroker for $512. I hope that price is OK cause I didn't price around too much before this purchase like I usually do. I been debating between a CZ 2075 and this Kahr. I went for the Kahr for the light weight. I'll let you know how it shoots when I get it...

I bought a new cimarron 45 colt model P in stainless. The problem is that after only a few cylinders of ammo the cylinder binds at the rear due to soot buildup. The brass comes out filthy all the way back to the head. The area behind the cylinder where the action is, gets gummed up and you...

My favorite target snubby load so far for my M-60 S&W is 6.8 gr of Universal Clays and a Rem 125 gr JSP. I get about 1050 fps and the round is accurate and doesn't bite the hand that shoots it. The load is still hot enough though to remind you that you are shooting a .357 mag. Very clean...

I have a S&W model 60. The DA trigger pull on this thing is waaayy heavier than the DA trigger pull on my 686. Is this normal and can anything be done to make it better? other than just backing off the mainspring tension (which i'm guessing will result in light hits). d.

I usually lube bottle neck cases with Hornady One Shot before resizing and it works fine. This weekend I tried loading some .223 rem for the first time and stuck the first 2 cases due to lack of lube. I had to switch to the RCBS wet lube to get the brass resized without sticking. I wiped all...

I just saw the new Uberti/Cimmaron model P in stainless in this months Handguns magazine. I looked gorgeous with the satin stainless and wood grips. Has anyone shot this revolver? I am thinking of getting it in 45 colt and was looking for opinions first. My local dealer wants $530 for one...

I am having a ball with a new Laporte electric trap I bought. I got it with wireless voice release. This is the TAH 85 pro with the built in wobble feature. This is a far cry from the manual traps i have used most of my life. I would highly recommend this trap to anyone. At the end of last...

My swimming pool can be my ammo dump??? http://www.howstuffworks.com/hydro-ordnance.htm d.

Does anyone know the minimum number of guns per year the BATF requires an FFL to sell before they pull the license for 'lack of business'?? I am interested in part time buying and selling guns but I'm not quitting my day job. d.

Last night on Mythbusters I saw something hilarious. They were demonstrating how a sabot works (because they needed to launch a man out of a culvert) and showed the sabot/bullet combo exiting the barrel. They also showed the brass following the bullet out of the barrel!!! Why is it so hard...

Is my cylinder opening too big? I am trying to figure out what you would consider the upper limit on cylinder mouth opening. The used M60 I just picked up is .362" What can happen (if anything) as the cylinder diameter goes up. At what point should the cylinder be replaced? Dave.

OK. I have got another question on my used M60 .357 snubby. What is the opening diameter of the cylinder mouth supposed to be. On my new 686 it mics at .358. On this used snubby it mics to .362. That seems awfully large to me. I thought the cylinder exit should be just about the same size...

I just picked up a set of crimson trace grips on sale at midway for my j-frame M60. They are $30 off in case you care. Sale price is $209 good thru 12/31/03. Merry x-mas to me.... Dave.

I just picked up a used S&W M60-9 and would like to get some suggestions on what type of bullet and load I should be feeding this thing. Most shooting will be at paper. I am assuming that my full tilt H-110 loads that I feed the 686 6" probably should not be consumed by this J-frame? Does...

I saw a used S&W model 60 today at the gun shop and couldn't leave it there without a home. It is chambered in .357 Mag with a 2-1/8" barrel. I would like to find out a little about it though and thought you folks could answer some of my questions. I would like to know about how old it is...