Search results for query: *

My brother bought one of these and I really like it,but the the trigger slap is so bad I can't finish a magazine. Any ideas on a fix? Thanks!

Recently purchased a Model 15-3 in nickel. Love the gun and shoot it well,but the nickel finish is in kinda rough condition. Would I be better off leaving it as is or having it refinished? Thanks!

Just bought a Bodyguard. Pistol is supposed to be 6 plus 1 capacity,but with 6 rounds loaded in mag I can't get mag to insert into pistol.I download 1 round and its fine. same issue with both mags and different loads. Any ideas? Thanks

I'm sorry if this topic has been covered, but what is everyone thoughts on replacement guide rods for Glocks?Looking at a Wolf guide rod and spring for a 17L.

I'm getting little triangle dents on the lip of my brass when fired from my Glock 19 . Is this normal or should I be concerned?

Loaded 185 lswc Missouri bullets over 4.5 grains of Titegroup. Firing these out of my Sig Nitemare the first round fires fine but the next round the slide will not fully go into battery. A mag drop, clear the round, install mag rack slide round fires and slide not fully into battery again...

How concerned should I be about powder residue getting into the trigger mechanism when shooting black powder cartridges in my Blackhawk? I had planned on a good cleaning with soapy water for the cylinder and barrel or should I do a complete tear down for the internal parts? Thanks!

Going to start loading 185 lswc Missouri Bullets for 45 acp. My Lee loading manual shows a minimum OAL of 1.14 using a starting load of 4.2 grains of Titegroup. What woud be a good starting point for oal? These rounds will be used in a 1911. Not looking for match grade accuracy, just a...

I love my Blackhawk,but the factory grips aren't doing it for me. I like the feel of the Hogue Mono grips,but in my mind they just don't look right on a single action. Looking for something more eye appealing and hand filling. Any recommendations? Thanks!

I'm loading 3.2 grains of Tightgroup with a 158 LRN. The problem I'm having if I crimp in the crimping grove my OAL is 1.46 and min OAL in my reloading manual is 1.475. Should I not crimp in the groove or will this be ok? Thanks for the help!

I've been looking at the .357/9mm Blackhawk and needing opinions. This will be a fun gun for me. Thanks for the help.

In my area BP is hard to find,but I see lots of Subs(Pyrodex,777,etc.). If forced to use a substitute which one and why? Thanks!

Could someone tell me where to find serial numbers for this shotgun? It is a 20 gauge with 26" barrels. Thanks!

Need a recommendation for a gunsmith to machine the cylinder on my Judge to accept moon clips. Thanks for the help!

Visiting with the family today my brother gave me back my Cobray derringer. I remembered I quit shooting it because the hammer started falling without pulling the trigger:eek:. Took it apart and filed some on the sear and now have good solid engagement with the hammer hook. Something that I'm...

My brother calls me the other night and tells me his 380 is having problems. Insert a loaded magazine and rack slide,but slide won't fully go into battery.He says you can push the slide closed. I had this gun a few weeks ago and had the hammer out removing some minor rust. Is there anything I...

I have the 4510 Judge with 6 1/2 barrel. Wanting a new set of grips and was curious about the size I need. Are they considered Small,Medium,or Large frames? Thanks for the help!

My Dad bought me a Browning Black Lightning Knive for my Birthday this year. So far I really like the knive. Does anyone know who is producing these knives for Browning? The blade says made in the USA. Thanks for the help!!

Can anyone tell me a little bit about this gun? It has a single non selective trigger. Possible years of manufacture? It doesn't say anywhere how it is choked. My Dad bought this gun at a gun show a few years back and I have taken it over. I see why now the english use SxS when hunting over...