Search results for query: *

A bad question for this thread but, We have a two story building and had a rain leak. The roof is flat with asphalt. We found a bullet hole in the roof that went all the way through the roof. Could any bullet have the force if it was shot in the air to do this.

I don't know so I will ask. What part is the yoke on the revlover. I had a brand new S&W and they had to adjust the yoke to get the cylinder to close. Thanks

I am looking at purchasing a new chronograph. Could anyone tell me a good one to purchase. Thanks

I saw on a thread that CCI now has a new box. I ordered a buch of primers CCI 500 primers and I have been having the primer go off but nothing else happens. I have shot about 5000 rounds and this is the first time it has happened. Can anyone tell me the problem. Thanks

I was cleaning out my dad's stuff when he died and found a French MAB 22LR BREVETE S.D.G.D. Can anyone tell we about this weapon.

I am considering purchasing a S&W 686, can anyone advise me on this weapon. Thanks

Since I have stumped the band on two other forums, I will asked on this one. I have two new S&W Model 619's. There is burn between the barrel & the cylinder and I can't get it to clean off. Any suggestions on how to get it off. Thanks

I have two new S&W Model 619 revolvers. Between the Barrel & Cylinder there is black burn there. It will not clean off. How do I get this off. Thanks

I read the other day on this forum that if you use a high grain bullet use slow burning power and low grain bullet fast burning power. I am new to reloading could someone explain this. Thanks

My Dillon 550b when you pull the handle down it will not drop a primer. If you pull the primer slide back 1/32 or 1/64 of an inch it drops the primer fine. Dillon has replace the primer slide 3 time. There must be something else wrong. I have also replace the bule tip on the primer magazine...

Without useing the gun value books. What would be a good price on a 1971 S&W Model 10-6 heavy barrel, stainless steel (custom job) only fired 5 time since 1971. Thanks

I have some round nose lead bullets for a 38 cal. When I went to the range, I put up a smoke screen. I think it is the lube on the bullets. Is there anything I can do to correct the problem. It also made my pistol very dirty. Thanks

I am reloading a 38 shell to be used in a 38 heavy barrel & 357. By useing the manuals how do you figure what will work in both pistols with the same load. The 38 can use a +P load per Smith & Wesson. Need someones help. Thanks

Need a good gunsmith for S&W pistols in the Oklahoma City area. Would appreciate someone help. Thanks

I am reloading 38 special 158gr RN with Power Pistol and I have excessive power floating around the air. People at the range thought I was putting up a smoke screen. I am useing 5gr of power. It is for a SW 38special and a S&W 619 357. Is this nomal for this power. I usually use Bullseye.

Someone please tell me the difference in soldering a part or glazeing a part in the repair of a revolver. Thanks

Has anyone fired the S&W 619. My wife wants me to buy her one. I would appreciate your information.

I purchased a Smith & Wesson Model 10 Heavy Barrel in 1971 New. I need to get an extractor for it. I ordered one from Numrich gun parts and 2 gunsmiths said it is not the right extractor. Numrich said it was. Where can I get an extractor for the above model.

I will be shooting 38 cal loads in both a 38 cal Special Smith & Wesson Model 10 and a Smith & Wesson Model 619 357. I am new to reloading and need to know if there will be a difference in to power load. Thanks

On a Smith & Wesson Model 10 heavy barrel, can the extractor be replace by an individual or does it need to be done by a gunwmith.