Search results for query: *

I have a scope base monted on a pistol someone used locktite on and I can't get the screws loose. A Ideas on how to loosen them without tearing something up?

I've got two questions. How well do deer decoys work and will painting the inside of my deer blind black help hide seeing movement inside the blind. Built the blind last year and wasn't able to put it up as high as I wanted to, it's about eight feet up in the air. It seemed deer were able to...

Can you use the Hornady 225 gr. .452 FTX bullet in 45acp pistol?

Is it worth while to paint the inside of a deer stand black? Will it break up the out line of the hunter?

Anybody know the current Mo. bullet code? Thanks for the info.

I have a Hornady Lock and Load progressive. When loading 45acp the press will not always eject the loaded round. Some times it will lock the press up and it's necessary to remove the shell plate to free it up. it only does this when loading 45 acp. I can't see any problem with the shell p[late...

I was recently loading some 45 acp using Lyman carbide dies. I noticed on some of the brass I was getting a very fine line around the bottom of the brass. It went about a third to half way around the case. It was at the bottom of the case just above where the rebate starts above the rim. You can...

I usually hunt by my self and as a result often had trouble loading a downed deer in the carry all on my tractor. I don't have a front loader which would simplify things so I had to come up with a solition for this problem. What I did was run a piece of 3/4 all thread between the ROP on my...

does anyone know how the Hornady electronic powder measure/dispenser compares with the RCBS unit?

Can anyone give me the name of the sharpener that uses a stone on each side of the blade that you push and pull back and forth. Thanks

Has anybody used the new plated bullets from Missouri Bullet Co?

I'm new to the AR platform and need some info. If I remove the hand guard on my AR will I have to re sight it? Thanks for the help!

I need some info on the AR-15 platform. Can they slam fire like the M1A. Tanks to all

I received some military 7.62x51 ammo in the battle packs. I don't from what country. The ammo shoots fine but when I went to reload the empty brass I had a problem. The brass will not fully enter the resizing die. Measuring from the case rim up about 3/8 of an inch of the case will not...

I recently purchased an R 15 and an AR 10. Both of them have scopes and are sighted in. If I separate the lower from the upper and reassemble them will it have much effect on the scopes staying zeroed?

Does anyone know how to remove the drive hub from the drive shaft on a Hornady Lock & Load AP press. Mine broke and I can't figure out how to get it off. The diagram shows a pin and it looks like i goes through the side of the hub into the drive shaft. The new hub does not have a hole in it for...

Well I went and did it, I've gone over to the dark side. I bought an AR 10 from Buds. It's an Armalirte DEF 10 and I love it. I put a 3x9 scope on it and used the Nikon p23 mount. What surprised me was the accuracy with this set up. Using 168 gr. Horady BTHP at about 2500 fps I was able to shoot...

I want to change the sights on my Para Ordnance P-14 Limited. Does anyone know what type of cut they use for the rear sight and the front sight?

I'm getting an AR15 and I'm not sure which one to get. The options are a Colt carbine or an Armilite. The Colt is a little higher but comes with iron sights. I also need some suggestions on a scope and on iron sights if I get the Armilite. Any and all comments would be appreciated.

Anyone have any experience with Windham SRC AR15 type rifle. I'm thinking about one but don't know much about them.