Search results for query: *

Another rural legend is that a piece of screen may stop a pistol bullet (or bounce it back at you).

What type of revolver? The thin cylinder walls on Ruger 6 shots are springy enough to have sticking problems with over pressure ammo. Have you fired any ammo which may have caused a leading or brass build up increasing the pressure?

The way the feds are going the shop might need a manufacturers license to "repair" and resell a firearm.

Well Kpin, I left that Godforsaken place over 30 years ago, for a better way of life, not running from the socialist gun laws. You're quick to condemn what you don't understand and that is a common trait of many back there. I wish you luck. I guess now that Oleg is gone the High Road no longer...

Quote -and in all truthfulness, is cowardly beyond belief. - Yes, that kind of attitude is one of the reasons I won't live back east.

1. Move out of MD. 2. Apply for permit in new state. I left MD a long time ago, but still have a couple of friends there, my understanding is that permits are very difficult to get. http://www.marylandshallissue.org/index.html

I used to fly often with a 2 rifle case. Always kept spare locks inside in a zip-loc with a note saying please re lock with these if necessary, just to insure guns didn't end up falling out of the case if the locks were cut for inspection. The TSA personel who have checked my firearms were...

Idaho is seeking firearms and accessory manufacturers to relocate there. http://www.magicvalley.com/articles/2007/10/28/news/top_story/123529.txt http://www.magicvalley.com/articles/2008/02/11/business/local_state/130601.txt

Could the victim have been shot with a revolver first, then a shotgun blast used to cover evidence of the revolver shot?

Going back down range to chase the deer away that were still laying down behind the berm, after you already went down range to set out targets. Looking under the seats for ear plugs, and finding only one.

Last years and this season's go to rifle- CZ550 Safari Magnum, hogs back stock 458 WM, loaded to 3.600" oal 450gn TSX .458" diameter bullet 2315 fps, chrono 10' from muzzle 5354 ft lbs energy 58.42 ft lbs recoil This load shoots easily under 1-1/2 inch at 100 yds from the bench. Twenty rounds...

Check in this forum, there is info on ground rod lathe turned bullets. http://forums.accuratereloading.com/eve/forums/a/tpc/f/3621043/m/177109731 http://forums.accuratereloading.com/eve/forums/a/tpc/f/3621043/m/188109851

In a few months, the Russians may have some spare "peace keepers" they can reassign from Georgia to help out on our border.

I don't go out into the wilderness alone, unarmed. Why should I expect a USFS employee to?

A LEO interacting with any one needs to be prepared for the worse. A gang banger, mass murderer or psycho isn't going to inform a cop he has a weapon. A legal ccw should be the least of his worries.

And I thought the list was just to hide a sleight on McCain.

How does the court define "in common use"? The number of MG's per million citizens before the registration closed would be an eye opener. Does anyone have access to the total number the ATF has on the books? Or is that info protected due to their loss of the files? Full auto would definitely...

When in doubt, you can always load a few rounds in steps from the starting load to your load to verify pressure is ok. Use the same run of cases or pull a few of your loaded ones down.

"The proper tool for the job" Might have been handy immediately post Katrina - Yes sir officer, just going out to fix up the neighborhood.

If I don't have justification to use deadly force, my mouth stays shut and my gun stays concealed. Seems like the best plan to stay out of trouble.