Search results for query: *

All of them. Hodgdon #27 was nearby when this pic was shot.

To make shooting .45 Colt affordable and to get away from the anemic factory loads. This evolved into loading highly accurate ammunition for my rifles.

I used to seat the rounds long but decided that I wanted my magazine fed rifles to feed the cartridges through the magazine. Someday I'll have a match grade .308 built with a minimum spec chamber, neck and a short throat I'll experiment with this again.

I bought a 625-5 from the SF Gun Exchange in 1993 when they first came out. In 1994 I bought a condo and sold the gun to cover closing costs. Silly me, I've never seen another one. IIRC it doesn't say ".45 Colt" but rather .45 Model of 199? on the other side of the barrel.

Parker Ackley experimented with bullet diameter and pressure and discovered that the diameter of the bullet has less effect on pressure than the chamber neck dimension. With a larger diameter bullet the chamber needs enough clearance for the brass case to expand and release the bullet. Once...

I like RWS (expensive), Lapua, Hirtenberger, US Military (LC and TW headstamps), Federal and Remington in my rifles. Winchester, Remington and Federal in the handguns. I keep all of my rifle brass sorted by headstamp, and sorted by rifle if the brass has been fireformed in a bolt action.

Are you calculating case volume or case wall thickness? I measured case wall thickness a number of years ago and got .012 to .014".

Set up your decapping die or use your sizing die but back it out a couple of turns and reset the decapping pin so it will make contact. Set the shell holder on top of the your standard shell holder and gently push out the primer. (Only necessary if you're using a decapping stem with an...

Giraud for .308 here, Forster and a drill motor for everything else. With the Giraud you can process over one hundred cases during a single commercial break. I posted a review of the unit here a couple of years ago. It might still be around.

I tried a few shots the other night and everything came out over exposed. I took this one tonight and it came out looking a lot better. Top to bottom, 625-2 Model of 1988 in .45 ACP, 625-6 Mountain Gun in .45 Colt, 625-2 Model of 1989 in .45 ACP.

Some powders respond very well to compressed loads. H4227, H322, Varget and H4350 have all responded very well to compressed loads in the appropriate cartridge and with the appropriate bullet weight. Magnum pistol powders like H110 or AA#9 need to be compressed or they don't work very well...

One of my favorites. Korbin Dallas: Shoots megaloid leader between the eyes "Anyone else want to negotiate?"

Quit being selfish and post some pictures. We promise not to drool too much. :-)

The amount of torque can make a big difference if the stock material between the trigger guard and receiver is a compressible material such as wood. This is less of a difference with a bedded rifle but still a factor. It becomes insignificant with a pillar bedded rifle because there is so...

Bedding is glass bedding the action into the stock. Gunsmiths do this by painting the action and trigger guard up with release and pulling it into the stock after painting the inside of the stock with fiberglass resin. Once it sets you take out the action, clean away any oozed excess and you...

In five different rifles I've tried the following with excellent results. FC Cases, FC210M Primers 44.4g Hodgdon Varget 168g Nosler J4 or 168g Sierra MK. 2.800 to 2.825 OAL I've loaded the same load in RWS, Norma, Lapua and Hirtenberger cases with excellent results. Shoots better...

Yes, 240-255g data works fine. Most .45ACP bullets do not have a cannelure. You need to taper crimp the loads and taper crimping may not hold under extreme recoil. Before 1994 I loaded and shot some 230g JHPs pushed by 11.5g of AA#5 out of one of my S&Ws and they worked fine. I could...

I don't believe that. There have been a number of 625 variants beginning in 1988, the most common being the 625-2 in .45 ACP. The original 625-2 model of 1988 was rollstamped and only made for one year although guns remained in retail channels for a couple of years. The 625-2 of 1989 was...

Shooting a S&W is like dancing with your mistress. Shooting a Redhawk is like dancing with your ex. The only down side to the S&W is that they require more maintenance and TLC.

You always size your cases after firing. .45ACP headspaces on the case mouth so it's important that the case be the proper dimensions to fit the chamber. I have not seen many manuals with a .45 ACP +P section. Accurate Arms had one in theirs but punked out by not publishing +P data for...