Search results for query: *

These are a couple of kitchen knives I have had and broke them. I just have the blades. What can I do with them or what would you do with them They are really thin

I have a decent marlin 39a with the 20" barrel. I am thinking about having the barrel and mag tube cut down to 16" to match the length of the stock /action when taken down. Also thinking about having the barrel threaded at the same time. This would make it similar to a 39TDS take down. Edit, it...

I am looking for a good Kukri, not some modern interpretation but close to an original. I am looking more toward the smaller size and does not need the little knives that commonly go with a touristy knife. Yes I know that I could use the Googles but looking for some of our expertise here.

the YouTuber Smartereveryday has a neat video on shooting BP cannons

The YouTuber Smartereveryday has a cool video on Slow-motion shock waves and has a short clip on the waves from a revolver. here is a screen shot of it and here is the video link, look around minute 8:30

I just busted one of my wife's favorite paring knives. It was a Cattaraugus. We liked it because it was so thin. We also have a few other cattaraugus kitchen knives. The french knife is sweet. I would like some recommendations for a replacement. Thin, less that 1/16" Short, around 2" I...

I just got this from a guy I work with here in Cambodia. It is forged from an old macpherson strut center post. about 1/4 inch thick and the balance point is about 1 3/4" forward of the handle.

I have a bunch of knives and do not use them alot. I live in Cambodia where 1/3 of the year it is hot and dry and the rest is hot and wet. I want to store my keepers here until I return to the States next May. Then I want to store them in my house until I return permanently some time 2027. I...

I am thinking about picking up a traditional Marine Corps knife from WWII, I am leaning towards a Camillus but would be open to what would be most practical. A MK2 that is USMC stamped is the top of my list. 2 things: 1, What do you suggest, and 2, Where is a good place to purchase.

From the Thread by Jim March over on TFL Here or here on THR.

Over here in Cambodia it is very humid and the edges of my knifes rust in a short time, I forgot a good wax like Renaissance and need to find something like that to coat my stored knives. I can sharpen them and in a few weeks the humidity here has take the edge off. About the only wax here is...

Would you buy a Semi Auto with an automatic empty mag release similar to the ejecting en-bloc like an M1 Garand? Would you also have a slide release built in to the full/partially full magazine?

Would you buy a Semi Auto handgun that automatically dropped an empty mag? and locked the slide back?

Copied some posts from the THR knife idea page to make a "Show your THR knife" thread.

If you find a maker not listed, please add a reply to the thread. This is not to be an active discussion thread. Holsters: http://2aholster.com http://3speedholster.com http://www.4cornersconcealment.com/default.asp http://www.5shotleather.com/ http://www.7xleather.com/chest_holster...

What is considered a true English pocket knife.

One by Sam1911 a couple of Schrade Sharpfingers, one USA model and one SS with wood handles A real nice Kershaw 1993-2 A couple of Case CV yellow handles

I really like a gold bead front sight, would a small bead that would look the same size as a front bead inset in the rear sight work. It would be similar to the 8 setup seen with tritium sights.

I took these posts out a a .25 ACP thread and I want to see how this can be proven. SEE the next post

I am looking to build a lightweight slick side tuber but I want a dust cover on a flattop upper. Basic idea Ace skeleton stock any lower, but a slick side with newer take-down pins would be great Rifle length free float tube fore-end one of the following; 1, 18" SS mid length barrel, low...