Search results for query: *

I have about 21,000 large pistol primers, leftover from a bulk buy me and my dad did back in 1995~ we bought about 300k of those plus various rifle and magnum primers, they've been kept stored in original boxes and spent their lives in vacuum sealed bags in the gun cabinets which run...

I picked up 3k of these and geez these are gonna be loading short searching around I see anywhere from 4.0-4.5 to 4.5-5.3 These are quite short so the max oal I'd probably run would be 1.080 or maybe 1.050 which would give me a little more ass in the brass for lack of a better term.. What's a...

I was given about 500 .40cal 180gr HST reloads "rmr sells pulled from time to time" the problem is my buddy factory crimped them with a lee die and my sig with barsto doesn't feed smoothly with anything lee factory crimped... I always use a Taper crimp rcbs and it will then shoot/feed...

Stupid cat ate 3 off the floor before I could stop him and my vet isn't answering his emergency line... I'm sure they'll pass, but any toxins ?

I have 1000ct of everglades 124gr JHP, bullet length is .583 I think XTPs are .600~? I'm trying to get a start/stop load using CFE Pistol. I found sparse XTP and Sierra data here and there that list 4.9-5.5, sound about right? Would like to get at least 1150 FPS

Time once again to buy some more bullets to load and was looking at these http://www.evergladesammo.com/bullets/handgun-bullets/9mm-124gr-jhp-rn-v2.html Hows the quality on everglades brand "or whoever makes them" vs say Zero. I was going to get a couple thousand. Scorpion evo sbr is gun of...

I managed to score 4 lbs of IMR 8208 XBR "never used it before" and was wondering if anyone has load data "min-max load data" using 60gr. soft points in .223 Rem. Hodgdon.com load data shows data for 60gr hornady V-max, but I have the 60gr hornady varmint soft points

Anyone have any load data using 180gr HP FMJ and n320 ? All I can find is lead load data and nothing for fmj... I usually use n340 or hs-6 but can't find any of the powders I use in stock anywhere, but I do have 2lbs of n320 on hand..

I was one of the few who had problems with older FC marked brass in glock back in the day and have since stuck with Winchester , RP and FEDERAL marked "in that order" my question is , I just paid $29 shipped for 500 .40S&W 1x sorted, SS cleaned , deprimed and sized FEDERAL marked cases...

I've got 150 rounds of .223 loaded with 26.6 grains of n140 with 75gr bthps which is like 2 grains over VV listed max :eek: that have been buried in back my ammo cabinet since 2006. I finaly got around to getting a bullet puller :o and was wondering if the powder is re-usuable "still good" ...

What is the min max using reloader 15 with 175gr. Sierra match king or similar bthp 175s in .308? Not trying to replicate damn military ammo I'm just using hornady brass cci benchrest primers oal of 2.801... some stuff says max grains 41.3 some show up to 45 grains....

anyone have any load data for hornady 68gr BTHP .223 using reloader 15 ? just need a start-stop grains. I was using varget but switched to RL15 since can't find varget.

anyone know of anywhere online with varget in stock ? sitting on a large amount of components but no powder :mad: called around within 200 miles all directions no luck. Hoping there's a place online with 1-4lbs in stock

Need load data for Gold Dot 180's in .40s&W using N-340 and HS-6... I Bought 1000 federal HST 180's from RMR and when I asked around I was told they should be loaded about the same as 180 gold dots. Problem is the only data I found on gold dots is for the 165 gr. version... Should I just go by...

Does anyone know where to find Speer Gold Dot 180's for .40/10mm *the bullets, not the loaded ammunition* "IN STOCK"... been trying to find some to order since like january with no luck, my local basspro and cabelas are sold out as well :-\. I had a 600 I bought and loaded back in 2010 and ran...

I've been using wipe-out: patch-out for years and only have a few drops left. "had 3 of the 8oz bottles" My routine usually goes: 1. carbon cutter 2. general cleaner to get harder stuff out "this is what I need more of" 3. bore brush then patch with general cleaner 3-a. stubborn copper removal...

Looking for loads for Plated Bullets. To be used are 180gr Berry's plated RSFP "round shoulder flat point" I'm thinking on switching to power pistol since it's cheaper at $17 per lb vs hs-6 at $24 and power pistol supposedly works better in .40. I've been having problems with HS-6 since...

I don't have much, as I either sold or gave away like 1000 of these already but I found a small bag of it today and I don't want to just toss them out when I can give them to somebody. It's not much but I have 75 winchester brass, and 25 Speer nickel you can HAVE. It's all 1x fired and tumble...

I have a replacement front nite-site coming in friday for my Sig p229 and could seriously use one of these. Would anyone be willing to lend or rent me one ? I'd pay for priority mail both ways plus a lend fee if anyone is willing to help me out

went from .357 back to my factory barrel of .40s&w and it shoots really low... tried the #6 front #8 rear and currently using #8+#8 and still shoots about 2+ inches low. It P.M.O that it shoots tight groups, but they are like 2-3 inches below where you want it to go pretty much if you want to...