Search results for query: *

  1. E

    How do I tell what choke my Franchi 48AL has?

    I just D/L'ed the .pdf file OK. It's just a little under 1.8 mb. If you want me to e-mail it to you, I can do that, send a PM. Sounds like you have the brass friction ring, but you're missing the steel friction ring and governor. The governor is the device that really decides how much...
  2. E

    Pics of CZ's with glossy blue finish?

    I like the blue, but I'd agree that the polycoat will hold up better for carry. My daughter and I are shooting a pair of SP-01 Tacticals at some of the action pistol shoots, and with 1,500 comp rounds behind each of them, the finish is holding up to the Blade Tech Kydex holsters OK so far.
  3. E

    How do I tell what choke my Franchi 48AL has?

    heviarti, sounds like reading the manual would save you a lot of aggravation. http://stevespages.com/pdf/franchi_48al.pdf
  4. E

    135 grain .40 Federal brand any good?

    The lighter bullets in the .40 S&W can be pretty snappy. The Federal load (#PD40HS4H) drives a 135 to 1,200 FPS. Generally speaking, bullets that are light for the caliber lose velocity quickly and do not penetrate as well as heavier, albeit slower, slugs. IOW, a 135 .40 S&W bullet is likely...
  5. E

    Allegheny Sniper Challenge

    Check your PMs Greebe. Ed
  6. E

    Estwing Weight Forward Hammer

    There's not much stopping a framing square either. . .
  7. E

    i just got an colt ar15

    Best bet is to call Colt with it. They've been very helpful when I've called, and will tell you the date and configuration it left the factory.
  8. E

    Cheap rifle ammo...

    Agreed 100%. Cheaper than Dirt (but just as nasty) isn't cheaper than anyplace and they are higher than most other places for their ammo. For comparison shopping, this is a good interactive site: http://gun-deals.com/ammo
  9. E

    A Quote from the Post

    qft . . .
  10. E

    forming 22-250 brass from .308?

    The .22-250 is a necked down .250 Savage case, and both are shorter than a .308 Winchester. I've necked .308s to make .22-250s. The purpose was to provide a very thick neck which could be neck-turned in order to produce a fitted neck condition in a factory style chamber. The rifle was quite...
  11. E

    Question for those with CHL/CWP's

    I always joke with the guy taking my prints about how easy it is w/o the cuffs. :D After having my prints taken in the military 30 years ago, then later for a C-III device, it just doesn't matter.
  12. E

    Difference between shotgun and rifle scope

    Rifle scopes are set to be parallax free at 100 to 150 yards. Shotgun scopes are set to be parallax free at 50 to 75 yards.
  13. E

    Ballistic charts vs. Real World results

    IMHO, given sufficient power to work at all, when it comes to hunting, bullet placement is 90% of it, and the ability of the bullet to expand and reach the vitals is the rest of it. Far too many people DO get caught up in the minutia of a few hundred feet per second or a few foot pounds of...
  14. E

    scope question

    Good posts by JWarren! I would add these comments: 1) Internal adjustment range: The bare minimum adjustment range required of a long range scope will depend entirely upon *your rifle's* exterior ballistics. Rifles such as the .308 will typically require 38 to 44 MOA over the base 100 yard...
  15. E

    Steel plate targets.... Newbie question

    So, where did the bullets go that bounced off?
  16. E

    Remington 700 Round Count - .308

    If it's in otherwise good shape and well cared for, 2k is really almost nothing in the life of a .308. Does the owner keep a data book or is he guessing?
  17. E

    Steel plate targets.... Newbie question

    I use 3/8" AR-500 material, which will resist deforming very well. We've shot it with 210 Bergers from a .300WinMag as close at 100 yards and the marks spray paint right off. We've hit it repeatedly with a .338 Lapua, which, while not damaging the surface layer, eventually causes a little...
  18. E

    colt match target 3rd series barrel loose

    Well, I reckon I was w-w-wr-wr . . . mistaken, this time. :D
  19. E

    colt match target 3rd series barrel loose

    Not arguing Jim, but a "Colt Match Target", new in the 70's . . . Is that not an AR-15 HBAR? If so, the barrel nut is loose. The barrel nut secures the barrel assemble to the upper receiver. Pull the handguards and you can see the serrated nut, and probably hand turn it a little. The barrel...
  20. E

    Steel plate targets.... Newbie question

    Actually, it's exactly opposite. The customary AR500 steel is so hard (Brinell 500+ surface hardness) that the bullet's energy goes toward fragmenting it and it literally splatters to dust. I have a bunch of AR-500 steel plates and they withstand .300 WinMag hits at 100 yards with no permanent...
Back
Top