Search results for query: *

I Traded in my SIG (357Sig) I Have remaining; Ten Pounds ( aprox 1000 ) .357 Sig > Brass. Once Fired, Agency Indoor Range, Pick up (That's the way it was sold to me) How about........ $30 .......plus shipping ...(It will all fit into one flat rate Box) What say You ...

Does anyone else have this problem? When counting out brass ( from the tumbler into 100 count baggies) I seem to get tiny "cuts" on my finger tips. Sort of like "paper cuts" only much smaller. They sting for DAYS afterward. Sometimes my finger swells up. Apparently the case mouths of the...

Alternate ( NOT H110) powder for 357 Rem Maximum Have been playing with two new barrels for my TC Contender (in carbine configuration). Hand Loading for: 357 Rem Maximum (180 and 158 grain Jacketed) and 45 Winchester Magnum (230 grain Jacketed) Working with the 45 Win Magnum...

Where is the "Best" Buy today for 357 Magnum/Maximum "jacketed" bullets ( 158 grain )

Ok I've been playing around without reliable facts for long enough. Time to ask for help from those who know more than I ( I would hope). I have a TC Contender in carbine configuration. I shoot at an indoor range which is limited to 25 Yards and "Pistol" ammunition calibers. I reload...

Want to load .45 Winchester Magnum for a 16"(+) TC Contender. I have some Hard Cast Lead 260 grain bullets. Am a little leary of driving Hard Cast lead down 16" of barrel. Afraid of unacceptable leading if I drive them too hard and I DO want stout loads ( what's the sense in wimpy .45...

OK I get it 45 acp dies ( I have some ) should load 45 Win Mag fine. I also have some 260 grain Hard Cast Lead 45 acp bullets (.452 I think) What load ? I want to drive them hard, but I don't want to lead up my 16 1/4 inch TC Barrel. What Powder - How much of it ?

Can we talk about .45 Winchester Magnum........... Where I shoot, I am restricted to "Pistol Calibers" I have a TC Contender in Carbine configuration and am constantly on the look for "Long" (16"+) barrels for it in "Pistol Calibers". Had an opportunity to pick up one in ".45 Winchester...

I have two versions of .38 spl Double Ended Wadcutter bullets 148 Hard Cast Lead - two lube rings wax filled ( They are "Zero" brand ) One is full flat on the business end and The other has a "Little Bump" in the center I intend to put them over 2.5 of CLAYS Question is: Do I seat...

Came by a batch of > Headstamp = . Tried to reload it on my 650. All kinds of problems. Hard primer seating - Sideways and upside down primers - Hard sizing - and >One Primer detonation on seating. I had previously just finished a batch of mixed brass ( No nickle) without any...

OK….. I have a persistent problem that I need to work out before it starts trashing parts. My problem is, that the small pistol primer disk on my 650 is “Jamming” while processing 9mm. I have already “bent” one Primer Indexing Arm, and am surely going to bend the new one that I took from...

Just got a .357 MAXIMUM Barrel for my TC contender carbine. It of course will take: 357 MAX, MAG, and/or 38 Spl Loaded up some MAXIMUM Cases ( new Remington Brass) with 180 grain HP Semi Jacketed and 21 grains of H110 Dont have a Chrony, but the data says it should fly at ~ 1900 fps @...

Just got a .357 MAXIMUM Barrel for my TC contender carbine. It of course will take: 357 MAX, MAG, and/or 38 Spl Loaded up some MAXIMUM Cases ( new Remington Brass) with 180 grain HP Semi Jacketed and 21 grains of H110 Dont have a Chrony, but the data says it should fly at ~ 1900 fps @...

Not sure where to best post this but I'll start here, I have a TC Contender in "Carbine" configuration ( Have the Pistol stock also but that's not where the question lies) I am limited to shooting at an indoor range with a max 25 Yard range and limited to "pistol" Calibers. I want to...

Reloading for my Benelli MP3S in .32 S&W L WC This is a "New" ( to me) gun. Using 100 grain Hard Cast Double Ended Wadcutter bullets 3.2 grains of Unique Powder Seating to just barely under case rim Lee .32 S&W Long 3 Die set "Roll" Crimping ( and final resizing) with a Lee Factory Crimp...

New tv series "Vanished" They talk ( seeemingly very knowlegablely) about a: Colt in caliber "30 Luger" with a Six Groove Left Hand Twist Barrel Anybody ever hear of such a thing ????? [email protected]

I've got this hankering in my head that just won't go away. I want to do .300 Whisper. Want to get a TC Contender Barrel (18 - 20 inches I think) Am going to mount it on a TC Contender frame in "Carbine" configuration with a 2-8 X Burris Scope Intend to shoot at 25 Yards from a rest...

This is amazing ( to Me at least ) I have a Dillon Toolhead (650) that I set up some time ago to load .38 spl I think that the bullet I used was a Hard Cast Lead Truncated Cone in 158 grain. Went to it today because I was out of 38 Special. I found three partial boxes of .38 Spl...

Bought one. Took two passes to get one that worked. Curious thing. I calibrated and zeroed it according to instructions. Everything seemed to be working ok I weighed a paper clip several times The scale gave me the same weight several times and returned to 0.0 when I removed the paper...

Super Redhawk - Clean as I could get it .44 Magnum Leupold 4x From a rest 25 Yards. HP-38 - 11 grains 240 Magnatech SJSP 1.60 Firm Crimp ( Can "see" the Roll with a glass ) What size groups could I realisticly expect to get if I build them right??