Search results for query: *

"SoftBall" is just the name MBC uses for their 230 grain LRN 18 BHN bullet. Here it is ---> SoftBall! <--- Seedtick :)

Aaah JL, I could be wrong but I think there's a little more to it than just "A big hammer on concrete." :evil: But keep an eye on it and let us know how it goes. Seedtick :)

+1 I agree with Kernel. This is my favorite. Seedtick :)

I'm not all that picky when it comes to pistol brass. I've learned it's best to not develop any kind of attachment to it, emotional or otherwise. Because I know it's likely I'll never see some of it again after running it through my very efficient semi-auto brass broadcasting machines. When...

I'm not familiar with Redding dies but I believe your - *1st die re-sizes your brass. *2nd die pokes out the primer and expands the inside diameter and flares the mouth. *3rd die seats your bullet and closes (crimps) the flare. I hope this helps get you going but if I'm wrong I'll...

+1 ...as do/would I. Seedtick :)

I'm in complete agreement with Mr. Nowell. Your H110 will work fine. It's just a bit to, ah, let me see....:scrutiny:..... ...obnoxious, yeah that's it, it's a bit to obnoxious for my taste. Seedtick :)

Or....... Maybe you could just try sizing a couple with your 9mm sizing die and see how it does? Please let us know what you find out. Seedtick :)

Cool story Mr. Dave! Thanks for sharing it with us. Seedtick :)

It looks as if this problem isn't confined to a 'particular' lot of bad primers. It appears to be an 'ongoing' problem with bad primers or maybe it's just Winchester's *S.O.P. Our bad lot number was CFL 448G. Seedtick :) *(Standard Operating Procedure) :mad:

FullEffect1911, What is the lot number on your Winchester primers? It would certainly be interesting, to me anyway, if it turns out to be CFL 448G. :scrutiny: Have you punched out any of the 'leaking' primers and given them a good going over? This thread from nearly a year ago will show...

Hey Lee, Look and see if they show the parts you need here at Lee's website. 3 HOLE TURRET PRESS PARTS Hope this helps. Seedtick :)

Got mine at Buffalo Arms. Stainless Steel Case Cleaning Media .041"x.265" Priced per Pound = $7.00 for 5 or more pounds HTH Seedtick :)

I don't reckon you saw one with my name on it did ya? They sure are purdy ain't they! Thanks for pics. I like looking. :scrutiny: Wait, that doesn't make me weird does it. :uhoh: Seedtick :)

I clean and lube the wave bearings on my SDB and I've never had any trouble. The times I've needed to contact Dillion I've always just sent them a message through their 'Contact Us' page. They usually respond in 24 hours or less by email. They will know what's going on. HTH Seedtick :)

Sounds to me like it would be more healthy for you to not read some of these postings. How do you feel when you read posts over at that accurateshooter place? Seedtick :)

RCBS Automatic Bench Priming Tool At Midway $103.99 At Natchez $87.38 At Big Supply Shop $71.34 Seedtick :)

I finally got a round tuit the other day and my small powder bar tops out at 18.3 grains of 2400. So I'll have to use the large one to run 45 Colt on my little SDB. Seedtick :)

I don't know about the 'sounding stupid' part but if it does.... We have the same stupid sounding question. Why couldn't you just go to a bigger hole and pin? He did say - I think a bigger pin would be easy and probably wouldn't even be noticed. Seedtick :)

Yep. I was thinking the same thing. They are running out of Wolf but they have plenty of the higher priced Tula primers. It also looks like the 'Special' on the CCI primers is over. :( Seedtick :)