hornady

General dimension question here: What is the W x Depth x H of a 250 bullet box of 30 Cal .308 168 gr BTHP Match™? Are these dimensions the same all around the table? Or, are they specific for each caliber? My reason for asking is I am making a reloading bench and I would like the dimensions.

Hello and I hope everyone is happy and healthy in this crazy time. My problem is this: PTX sticks as case is removed from powder drop through expander. I have done many, many hours searching here and the internet. I have cleaned, polished, lubed, removed, reassembled, raised, lowered, adjusted...

Good morning folks, Does anybody happen to know the nominal length for Hornady's 124 Gr. and 147 Gr. FMJ RN bullets? I can't seem to find it online anywhere. I'm just starting to work up loads for some RMR 124 and 147 Gr FMJ bullets (just opened the bags and measured some sample bullets this...

I love this hobby. It seems I discover a new labor saving device every couple of months. Since my first loading session I’ve been emptying my powder drop after every session. It is a bit of a pain to remove the drop to slowly pour from the tube back into the powder bottle...praying that I don’t...

Dear guys, I write this post referring to some Hornady Items: 480083 398067 These are the seating dies rubber flat washer, and the taper crimp seating O ring (not the ring below LNL Bush). #7 and #8 in attached Exploded I am in Europe, here it is possible to find only one item (the flat...

I have some 30-30 cartridges I want to reload with Hornady Interlock 170gr. JFP. However, the only powder I can find at my local store is the Hornady/Hodgdon Superformance, and I can't find ANY load data for this powder and cartridge. Does anyone have any data for this, or this particular...

Just want to start out and say hi to everybody. I’m new to the forum, but I’ve been reloading for a couple of years now and I must admit I have been following this forum for a while now off and on. Everyone here seems to have some great insights from differing perspectives which is a big help...

Just getting into reloading 9mm and have a few basic questions. Some of the brass I have is pretty nasty from being at an outdoor range. I picked it up knowing I was probably going to wet tumble and saw some before and after pics of wet tumbling with stainless media, so I picked it all up...

Skulking around some rural gun shops over Columbus Day, I scored a box of Hornady 35 grain XTP bullet in .251 diameter (for use 25 ACP). Normally, when I develop a load, I will load ten rounds at the Starting load, followed by ten rounds at each increment between the Starting load and Maximum...

Last year I started using Hornady Unique case lubricant. On the package they say, "a little goes a long way" and after I developed a light enough touch that I wasn't overdoing it, I was surprised to find that I had lubricated more than 3,000 cases and still had barely used any of the tub...

Good morning, everyone. I have a few questions pertaining to reloading for my WOA Varmint 223. I think I know the answer to the first two, but can't find the answer to the last one for the life of me. Any help is much appreciated. 1) I have some once fired brass from Mil-Spec (or close to it)...

I am getting ready to start working up a 9mm Luger load using HP-38 with some 115 grain bulk bullets that I bought some time ago. The bullets look like Hornady XTP bullets except that the transition from the body of the bullet to the ogive is not quite as abrupt as on the Hornady. The bullets...

I have read several posts today where people were talking about using 75, 77 or 80 grain bullets in .223 Remington. Why is that? What I'm wanting to know is what makes you, as the person responding to the question, choose the bullet weight that you do - particularly if it is heavier than the...

I know I'll catch hell for not checking from the get go and loading 100 rounds and then realizing my mistake, but admittedly I made an error when full length resizing my brass and set the shoulder back too far and now there is between 0.009 and 0.010" of difference in the shoulder of a fired...

I'd like to apologize in advance, but this may be more venting than actually presenting a solvable problem. I have been reloading for about 10 years. All of it on a Hornady LNL press. Pistol and rifle. In that time I honestly don't think I've even ONCE made it through 500 rounds without having...

Hi this is my first post on THR. I run a Lee load master for pistol calibers and want to upgrade my powder system. I currently run the auto disk as I have for years but want something not only more accurate but a little nicer quality than the normal Lee stuff. So ideally what I want is the...

Hi and thanks for the help in advance, I'm fairly new to reloading but have a done a few hundred rounds of several different calibers, so starting to get my head around it. Today I bought some 70gn Hornady GMX (guided metal) projectiles for my .223 to use on pigs. I have been using 62gn...

Does Hornady test these with actual brass? I recently purchased a Hornady #21 shell holder so I can start reloading for my carcanos. After a long hassle with the post office, I finally got it yesterday and this morning was going to deprimed all my brass. However, none of my 7.35 or 6.5...

When I posted the video comparing the 9x18 Hornady FTX against a 9-Luger JHP and a .38 Special JHP, many of you asked me to test more 9x18 rounds (as well as other .38 SPCL rounds - that test is coming). You asked, I tested - ACCURACY, PENETRATION & WOUND CAVITY. Buffalo Bore 95 gr +P JHP...

Y'all I swear upon the memory of Elmer Keith, John Browning and that Garand guy that I'm not trying to start a flame war _but_ I'm just about set to file the order for a dillon 650 but I'd be interested to hear opinions of people who have a dillon and a hornady or rcbs progressive as to which...