Cast or Coated

[GeoDudeFlorida]

Like I said @74shooter you better learn to cast and powder coat your own because that’s the only topic that will get discussed around here.

 

[41 Mag]

Does the 45-45-10 dry. The formula they use on 22lr would be amazing to know

So as far as how much it dries really depends on how thick it's put on. I like to have to look hard to even tell it's there, but usually there is enough in the groove to see a slight tan. Warming them up with the hair dryer and using JUST a dribble seems to be the trick for the SWC's for the ACP.

Now on my 454 bullets they get a bit more, and sometimes even a third coat if I don't like how they look. After they are loaded I will take a rag with just a drop or two of mineral spirits and wipe the noses off to minimize dirt collection.

Don't get me wrong, Cannula Red constitutes the majority of my revolver and rifle bullets. I shoot on our rural property so what bit of smoke there is isn't an issue. I don't have anything fancy to size with, just a Lyman 450, an old Saeco I picked up and refurbished, and some Lee push thru's. It all works for conventional lube. And a couple small toaster ovens do the PC justice.

 

[dannyd]

It's just like the Stink and mess of the Lube. PC guy's get it on the front end and Luber's get it on the back end.

Use Hi-Tek on the front end MEK or Acetone definitely rough chemicals, so you need a the Hazmat gear also Powder Coat paint the same way.

It all works and I do try new things.

Going to the range see you later.

 

[74shooter]

Like I said @74shooter you better learn to cast and powder coat your own because that’s the only topic that will get discussed around here.

No interest in casting and coating, was inquiring concerning the pros and cons of purchasing hi-tech coated vs lubed lead, unfortunately the thread was jacked, however several folks responded to the original question, thanks, much appreciate those who did, thanks for the suggestion geodude.

 

[Y-T71]

No interest in casting and coating, was inquiring concerning the pros and cons of purchasing hi-tech coated vs lubed lead, unfortunately the thread was jacked, however several folks responded to the original question, thanks, much appreciate those who did, thanks for the suggestion geodude.

Fair enough.

Sorry, if I hijacked your thread.

 

[dannyd]

No interest in casting and coating, was inquiring concerning the pros and cons of purchasing hi-tech coated vs lubed lead, unfortunately the thread was jacked, however several folks responded to the original question, thanks, much appreciate those who did, thanks for the suggestion geodude.

I personally think Hi-Tek is one of the best coating for bullets, but unfortunately I used MEK and Acetone for about 40 years and now can't get near it without bad consequences to me.

nice article on Hi-Tek

https://www.theballisticassistant.com/hi-tek-coating-cast-bullets/

Also sorry if I hijacked too.

 

[CraigC]

No interest in casting and coating, was inquiring concerning the pros and cons of purchasing hi-tech coated vs lubed lead, unfortunately the thread was jacked, however several folks responded to the original question, thanks, much appreciate those who did, thanks for the suggestion geodude.

If you're buying bullets and shooting outside, I don't know why you'd care. I don't. I honestly don't know why people bother with powder coating their bullets before they send them downrange but casters like to tinker. I like to shoot.

 

[dannyd]

I am Definitely in the Tinkers bucket. I change press manufacturers about every 7 to 10 years. Been Red, Green, Blue and Red.

 

[GeoDudeFlorida]

If you're buying bullets and shooting outside, I don't know why you'd care. I don't. I honestly don't know why people bother with powder coating their bullets before they send them downrange but casters like to tinker. I like to shoot.

Yup. As long as I’m not on the receiving end I could care less. I buy what fits the use scenario and my budget. Both are slim.

 

[DMW1116]

I just got a box of Gallant 135 grain coated 9mm to try after great siccess with their 125 grain 0.358 bullets. We’ll see how they do in a week or so.

 

[Bill M.]

I do not cast. I like buying, loading, and shooting powder coated bullets. I do not see a downside to coated bullets. I also shoot some plated bullets in 9mm and light weight in .357. I like them too.

 

[King Medallion]

I use both. My few attempts at coating have been epic failures. I do like Berry's plated bullets for my 45's.

 

[dannyd]

If you buy bullets and shoot 38 special or 357 magnum try the Missouri Bullets Hi-Tek match no lube grove 158 SWC. Great bullet just get your flair right, so you don't scrape off the coating also beveling the inside of the case mouth helps too.

 

[DMW1116]

My next test will be some 158 grain SWC bullets. I like Acme but Missouri might be an option too.