Does anyone remember the kinetic bullet puller made from iron pipe that I believe was in an NRA article from years ago? I had the instructions on building it but can’t find them.
Has anyone dealt with them before? I have been looking at his 3D printed case feeder for another Hornady LNL i recently purchased. Had a couple emails with him and nothing going on two weeks. It’s a bit pricey and with shipping is getting close to what a Hornady case feeder would cost.
It does...
There is an issue with the Glock sleeve where the firing pin slams against the bottom slot in the sleeve. Only way to replace the sleeve is to buy a complete firing pin assembly and they are as rare as hens teeth up here.
Farrow makes an aluminum one and was wondering if anyone is or has tried...
I bought a bunch of these for a really cheap price. Pulled a bullet and was surprised at what I found. I’m not that schooled on wad cutters and have not seen one of these bullets before.
Left is a Lee I cast, then a BDX brand HBWC, then a Hornady HBWC then HBWC one I pulled from the Federal. Had...
I found a can of Herco that was given to me a few years ago by my BIL that he had for 20 years. Thought I would try it in 45 Colt. Used 9 grains under a Kieth style that dropped at 263, powder coated and a Federal magnum primer. Going to pick up a new can of Herco and see if I get the same...
Has anyone changed the reset spring in one specifically a Glock 44? I need to know how the spring bar or whatever it is called that the coil spring goes over and fits into the housing. There is a up angle and a down angle to it.
I just got one a couple days ago. Put 100 CCI minimags, 100 Blazer and 50 Stingers through it and no issues other than I had several fail to lock on last round but discovered I had my thumb against the slide lock and that’s what was causes it.
I have other 22 handguns so I don’t want this to be...
I never noticed this on the #32 for 45 Colt until the other day. It always had ejecting issue as well as being slightly out of time with sizer and PTX when using it. All my other shell plates have this bevel cut into them except the #32 plate.
Can anyone who has a #32 plate check it to see if it...
I never knew about it until AR-Bossman mentioned it in another thread. Of course I can’t find it available up here in Canada but that doesn’t mean it isn’t I just can’t find it.
So I thought I would try a spacer of some sort and only thing I had were a couple of brass spacers used on the water...
After having major shoulder surgery last December I was bored on the weekend and thought I would try doing some reloading. Big mistake as while trying to change powder measure rotor to pistol I turned arm wrong way and watched as the rotor took a swan dive out of my right hand over railing down...
Any chance someone with it could run a load for me? It’s 27 grains of H4198 in a Winchester 45/70 case with a standard and magnum Federal large rifle primer with a 405 grain Lee hollow base cast bullet that is powder coated.
My Labradar shows an average of 1281 FPS and would like to know the...
I’m hoping someone with it can help me with the numbers especially pressure for a 45 Colt loaded with 11.8 grains of Tightgroup under a 250 grain plated bullet with a standard large pistol primer. I’m not looking at doing this as it happened in a SBH and everything is ok. But it about made me...
Im having an issue with this expander. I just got it awhile ago and tried using it today can not get it to set up properly. Didn’t pay much attention to it but now looking at it I can’t see how it is going to work.
The Colt 45 is on the left, 44 magnum next, 38/357 next and 9mm.
Anyone else have...
Shot some 45/70 I reloaded with Goex. From time of shooting to decapping and putting in a jug of water was about an hour. Let them soak, shook jug and rinced. They then went into wet tumbler with pins for and other 45/70 brass that used smokeless for a couple hours. They are all new Winchester...
I’m using a start load at 27 grains H4198 with a 405 bullet in my Springfield Trapdoor. It’s the lowest pressure load in Hodgdon load data. I loaded a few but haven’t been able to get out to try them yet.
Anyone else using this powder?
I have to quit trying to do two things at the same time and...
A few weeks ago my RCBS one finally broke after many years. The head broke off several times and though I had glued it I thought I would try the Hornady one.
BIG mistake. Though it looks good and actually feels really good the cap end broke the first time I tightened it. Took it back and got...
I went shooting with my nephew yesterday and he has these to pistols. Man I couldn’t hit the side of the proverbial barn with them. I shot the 45 off of a rest and could put them pretty much through one hole at 7 yards but anything past that it looked like a shotgun. The 9mm was a bit better...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.