Search results for query: *

The length of the bullets can be different so depending on load length there could be more of the bullet in the case changing case capacity. This can also effect the load amount.

I have thought about doing the same. What is the wait time now? Are you having the mount cut in front of the rear sight or having the rear sight removed and using the notch built into the 507

Thanks, I talked to CGW yesterday they are 3-4 months out on getting it done. I am just concerned if the small window size will be a problem seeing the dot and the smaller sight picture.

I am thinking of putting a MRD on my PCR. The holosun 407k fits the size of the slide good but has a pretty small window. For anyone that has used one are there any down fall to using one compared to a 407c or a Vortex Venom that have a bigger window which are the other ones I am considering.

My son put one on a 12ga for turkey hunting and I think it worked fine on that

At Olin corp. in the primer shacks they have anti static floors, the workers wear anti static shoes and once they get the mix into the mixer they leave and do the mixing by remote control watching it by camera. When they transport the primers thru the plant red lights flash and all traffic...

I occasionally lose a primer to the floor but it is usually because I got sloppy with with how I was using it. If its set up correct and you're having problems it's probably operator error not the equipment.

You have to be 21 in IL. to have a hand gun or ammunition for a handgun. It has been like that for a long time. I THINK they changed long guns to 21 a year or two ago also

I had a similar issue. I sent my trigger parts off to have them worked on to lighten the trigger pull. Mine would multi fire when I would slowly release the trigger to reset it. I messed with it a little but couldn't fix it so sent it back and had them redo it or maybe they gave me a different...

Not sure there is such a thing as to cautious. I use a turret press so I finish each round as I go. I check powder weight and aol about every 20 and look in every case as I go. If the length that you have set plunks ok you shouldn't have to recheck everyone. Do what makes you comfy, better to be...

When I started doing 223 most everyone said no crimp necessary. I also have FCD but never used it and haven't had any problems

The East Alton Il. plant makes primers. They also have shot towers for making lead shot, the brass mill is there where they make brass and they have different buildings for loading different kinds of ammo.I'm not sure what they still do there now because they have been moving some ammo...

5.56 rounds are usually hotter than .223 rounds therefore it is recommended to not shoot 5.56 rounds in a .223 chambered gun

If they are moving production but leaving corp. where it is aren't they still paying the high taxes in the corp. state. Sounds like they are just trying to save on the cheaper labor

When I set the screw on the drum I take the hopper off so I can see if the drum is lining up with the hole. If it's to tight the drum won't rotate all the way back, if it's to loose it will go past a little. How hard you let the handle come up can effect it also

I would like to be put in for Crowcifier666 bullets. I will put up 50 Midsouth varmint nightmare 55gn hp .224. Thanks

Thanks for the info. I am going to use a adjustable stock. The video above said there could be an issue in cold weather if you have to heavy of a buffer so don't want to get into that when hunting. I might just go with the H buffer and call it good, it's not like a .223 recoils to hard anyway

I bought a rifle length 20" 5.56 upper from PSA that I want to put together a lower for. I have a lower with a 16" mid that is a standard PSA mill spec buffer. I put the 20" upper on it and it seemed to work fine. Should I just get another one of these or is there a different set up that would...

The last couple posts covered everything pretty well. The only thing I saw was that I have never had to show a FOID card to buy powder or primers. I think your only issue may be getting changed over to a IL. resident with the guns, getting things done in the right order stay legal. Go to the...

vaalpens, I got the brass thanks