Search results for query: *

I have had a Lasermax installed on my Sig 226 which has worked great. This is the setup where the stock guide rod is replaced by the Lasermax guide rod and spring and the laser is activated by the new take down lever which has an internal button. Something had gone wrong with the take down...

I reload for 9mm and 10mm and notice that there are black soot on the side of most brass i pick up. I dont see this as much with a factory loaded round. I use the Hornady dies that seat and crimp in one station and wondering if maybe the crimp is not right or tight enough??? There are no...

First time i have reloaded for the 9mm and decided to go with AA#7 for my heavy 9mm reloads since i use them also for the 10mm 155gr variety. I chrono'd these factory rounds out of the M&P9c which has 3.5 inch barrel and completely stock minus trigger work. I am listing the average of a five...

I have an M&P9 compact that i love and want to reload 9mm. I have been reloading 10mm for my Glock 20 and immediately got an aftermarket barrel for better chamber support since i am loading hot 10mm loads. I was wondering how the chamber support in the M&P9s were and if an aftermarket barrel is...

I got the Hornady 50BMG kit and have prepared some cases and ready to load and assemble. I am having a difficulty figuring out the amount of crimp to put on the bullet. The ammo will be fired in a Barrett M82 so it will be a semi of course and would require a crimp. The way i set up the...

I just got a Hornady tumbler and Frankford Arsenal corn cob media. I put 30 cases of 50 BMG in the tumbler and after three hours the cases look pretty clean and shiny but the necks still have a lot of crud on them. I let the tumber go for three hours straight with four teaspoons of brass...

Here are a few brass from my session this weekend. These were shot in lone wolfe barrel from Glock 20. The brass cases are from Georgia Arms 180gr FMJ range ammo which chrono'd 1085ft/sec so is not a nuclear load. The nickel brass you see are from DT 135, 180 and 200gr loads. The cases...

I have decided to reload for my 10mm Glock 20. I have used to reload for a few years during my college times for my 9mm and 7mm Rem Mag rifle but have not reloaded in 20yrs but still very familiar. I want to load large numbers as in about 5,000 rounds once i have my load worked up. These will...

So have been meaning take my G20 to the range for sometime to check some numbers and compare DT to some of the other 10mm i have piled up. I just purchased a nice Chrono at Midway and decided to try it out. Weather was 93deg today so definitely nothing that should limit velocity. I am just...

Well i have been shooting for a better part of 15yrs and i have always been an import guy. My first hand gun was a Sig 226 in 1992. Since then i have always owned either Sigs, H&Ks or Walthers of all kinds. My current everyday carry piece is the Walther PPS which i love. It is slim, accurate...

I just ordered a set of XS Big sights for my Walther PPS and it came in Friday. Installed the sights and really liked how they looked. The acquisition of the front sight is super fast. I tried it with lights off and the front and rear lit up pretty bright green. I allowed the loctite to dry...

If you are looking for cliff notes then this is not it. Please take a few minutes to read and watch the video. There is substance here. Well i am finally back from Port au Prince, Haiti and it was an incredible experience. I almost didnt make it down there. Our private charter was canceled...

I own a an FN FNAR which is a .308 semiautomatic made by FN. It is basically the BAR with a pistol grip and cold hammer forged barrel but the action is all BAR. I sent my rifle to a gun smith to have the barrel threaded for a muzzle brake installation, and after i have received my rifle back...

I own a an FN FNAR which is a .308 semiautomatic made by FN. It is basically the BAR with a pistol grip and cold hammer forged barrel but the action is all BAR. I sent my rifle to a gun smith to have the barrel threaded for a muzzle brake installation, and after i have received my rifle back...

Looking for a all around knife. I would prefer a blade length in the 6-7" range. So far i have looked at the RAT-7, SOG Seal Team, RAT Cutlery RC-6, Becker 7 and Cold Steel SRK. The more i read the more confused i am:) Money is really not an object. I would prefer a $200 knife that per say is...

Took out the Barrett M82 CQ this weekend for some fun. The range i went to only had a 100yard range but i decided to do some controlled shots and also some rapid fire shots to explore the our limitations combined. I was quite impressed actually. All the talk about how the M82 is not "accurate"...

I have a Sig 226 with threaded barrel, trigger work, and AAC Evo-9 can on it that is primarily a home gun that obviously will not be carried. I always wondered how a red dot such as Jpoint/Docter or Burris FastFire would work. I think that sight acquisition would be faster comparing to standard...

I know a dealer that is selling a brand new Sig Blaser Tactical 2 in .308 with the threaded barrel. What is the going price on these rifles?

I have an older early 90's Sig 226 without the light rail but wanted to mount a flash light to it. What are the options available? I have tried to search but it seems most attach using rails that come with the newer ones. All input appreciated.

I saw this posted as news about a shooting, and the more i looked at the picture i realized there are a few things wrong with this picture. If i was the head of the police dep or the pictured officer's senior i would resign:)