Search results for query: *

I am looking for a SD/HD load for an AR pistol. It must cycle reliably. I will be using Blue Dot powder and Sierra 77 match bullets. Firearm will be an 11.5-inch barreled Colt upper with pistol brace lower. Any good loads you would recommend?

I can't find good online load data for this purpose. I plan on using 125 JHPs (maybe 110 JHPs if I can find any) and powders I have on hand: Unique, WST, Accurate #5. Any recommendations? Thanks

Fiocchi Defense Dynamics 380 acp 90 gr jacketed hollow point Fiocchi 380APHP Defense Dynamics 380 ACP 90 gr Jacketed Hollow Point (JHP) 50 Bx/ 20 Cs | BattleHawk Armory Has anyone used this brand? I recommended it to my brother for his wife's S&W Shield EZ. Comes in a box of 50 for less than...

I've installed one before a few years ago and love it. Today I tried to install a new one on another lower and noticed it has a fixed hammer pin. I've watched a few videos, but they either use the older style or completely skip over how they installed the "new" fixed hammer pin type. How do I...

Where to get accurate info on date of manufacture. Search sends me to Savage99.com which says it's an invalid number. Is there another source? Phone call to Marlin is a dead end. Maybe Ruger will have that information eventually. M

I have a lot of 150gn Hornady FMJ-BT bullets and H414, IMR 4895, Varget, IMR 4831, etc powders None of my manuals have data equivalent to M2 ball. Suggestions from owners? M

Who currently makes them? I had a barrel shortened to 21 inches and threaded for a set of chokes 25 or so years ago but I can't remember who it was. M

Scored one today at the swap meet. Nice looking walnut stock, screw in chokes, very clean. Also met the guy with the Ithaca 20 Featherlite again. He is new to the area and keeps guns out of state. He also has his mother's Ithaca 16 gauge he is looking to sell. First time I met him he bought a...

I met someone today who has a model 37 20 gauge w/26 inch barrel made in the 60's he would consider selling. I asked if it was the Featherlight model he said he didn't think so. I haven't seen it and don't know the condition or what he would be asking for it. When did Ithaca first change to an...

I will be reloading for a friend. I plan on using heavier bullets (95-107gr) and have Varget, H414, IMR 4831 and a few other powders available. Any favorite loads? M

I recently bought some 9mm ammunition and noticed the cases were 2-piece nickel plated Winchester headstamp. Anyone try to reload this yet? M

A friend here wants my brass. I have 140 pcs M118 most once fired. I am trying to come up with a reasonable price for him. Any ideas what this is worth? M

Pre 1980 (1974) 2 3/4 chamber, VR, full choke, w/ extra Imp Cyl barrel. Exc cond. I'm considering selling it as me and my shoulder are getting too old. Is there any reason it wouldn't be in the same price range as a good used newer one? (350-400$ maybe +100 for extra barrel) A friend is coming...

Recently picked up an old Bushmaster XM15 and found out the front is non-F marked and not compatible with the rear GGG aperture sight it came with. I have a taller post on order but was wondering what detachable handle or bolt-on rear sight might work in the meantime? Anyone got any ideas? M

I just ordered some of the new Israeli bandages to stop bleeding (from say a gunshot wound) which prompted this discussion with the wife. Curious what the "legal eagles" here have to say about the legal ramifications if one does or does not make an attempt to save the life of someone you just...

I was wondering if anyone else here has one and can tell me anything about their "proprietary AKM bolt". Looking to purchase one. Haven't been able to pull a picture of one or any other info. I called them today (Friday) and left a messgage with Frank. I am guessing their bolt is something "new...

Anyone have one of these new Gen 4 versions? Nothing very recent in THR search engine. Also looking at the S9-A1. M

http://www.denverpost.com/2016/12/15/aurora-17-year-old-gets-20-years-in-prison-for-wounding-off-duty-deputy-in-one-in-a-billion-shootout/ I'll bet Chuck Norris could have made that shot... M

Not high speed or even low drag but Joe is down to earth and 100% practical. I'll have to get me a cool decal ASAP. LOL M

sold...