Michael Tinker Pearce
Member
- Joined
- Oct 23, 2016
- Messages
- 1,577
A few weeks ago someone handed me an 1858 Brass-frame Remington kit. All the bits were aas-cast, the barrel wasn't secured and a couple of screws were missing.
I spent some time mulling over what to do with it and decided to go a little 'out there.' I turned the barrel down to round, cut and crowned it at 3-1/4", then removed the loading-lever and cut back the front of the frame. I bored a chunk of brass for the barrel and a long cylinder-pin I made, then made a steel plug that fit the loading-lever plunger hole and mounted it to the brass piece with a screw. I mounted and dapped the barrel, then silver-soldered the brass extension on over the barrel. Once that was done I shaped it to match the frame. I also silver-soldered an extension on the grip-frame and cut a 'pinky-notch' in the front of the frame.
I also brought the frame to a proper finish, mostly using increasing grits of wet-dry sandpaper.
I made a set of Spalted Maple grips, then went to work on the mechanism. The hand (which moves the cylinder) was some kind of trash metal and was chewed up, so I replaced it with a new one fabricated from 5160 spring-steel. I also needed to replace the mainspring with a stronger one. I had a cylinder for a .44 Colt conversion on-hand, so I made a new breech-plate with a rebounding firing-pin and timed it so that it can be swapped in to replace the percussion cylinder. I didn't cut a reloading port; either cylinder must be removed for reloading. With the cartridge cylinder the cylinder pin can be used to punch out the empties.
I made and mounted a new front-sight, and the gun was essentially complete.
The screw in front of the cylinder can be turned 180 degrees with my fingers, which releases the cylinder pin and allows removal of the cylinder. It's labelled 'L' for locked and 'U' for unlocked.
As part of a previous deal I had been given a glass-topped case for a n 1858, so I stripped the interior and fitted it to hold the gun, the extra cylinder and some accessories. I made a cover-piece to fit inside the glass and hold everything securely in place. The interior is lined in green felt.
The tools include a cleaning-rod, a screw-driver, a ball-setting tool and a bespoke powder flask that throws the correct charge for this revolver. There is room for a tin of percussion-caps, balls and wads as well as fifteen rounds of .44 Colt ammunition.
Some details of the gun- the breech-plate for the cartridge cylinder follows the contour of the blast-shield, allowing you to easily determine if the cylinder is loaded.
The rear-sight trough is deep and wide, and actually provides an excellent sight picture for a gun of this type. The gun is very comfortable for my hand and the gun points quite naturally. I'm really looking forward to getting this to the range and shooting it, both as a percussion gun and with cartridges. It will be interesting to see if it hits anywhere near point of aim...
Oh, for display purposes the internal cover can be removed so that the gun can be seen through the glass.
This is one of my more elaborate builds, and I am quite happy with the way it has come out.
I spent some time mulling over what to do with it and decided to go a little 'out there.' I turned the barrel down to round, cut and crowned it at 3-1/4", then removed the loading-lever and cut back the front of the frame. I bored a chunk of brass for the barrel and a long cylinder-pin I made, then made a steel plug that fit the loading-lever plunger hole and mounted it to the brass piece with a screw. I mounted and dapped the barrel, then silver-soldered the brass extension on over the barrel. Once that was done I shaped it to match the frame. I also silver-soldered an extension on the grip-frame and cut a 'pinky-notch' in the front of the frame.
I also brought the frame to a proper finish, mostly using increasing grits of wet-dry sandpaper.
I made a set of Spalted Maple grips, then went to work on the mechanism. The hand (which moves the cylinder) was some kind of trash metal and was chewed up, so I replaced it with a new one fabricated from 5160 spring-steel. I also needed to replace the mainspring with a stronger one. I had a cylinder for a .44 Colt conversion on-hand, so I made a new breech-plate with a rebounding firing-pin and timed it so that it can be swapped in to replace the percussion cylinder. I didn't cut a reloading port; either cylinder must be removed for reloading. With the cartridge cylinder the cylinder pin can be used to punch out the empties.
I made and mounted a new front-sight, and the gun was essentially complete.
The screw in front of the cylinder can be turned 180 degrees with my fingers, which releases the cylinder pin and allows removal of the cylinder. It's labelled 'L' for locked and 'U' for unlocked.
As part of a previous deal I had been given a glass-topped case for a n 1858, so I stripped the interior and fitted it to hold the gun, the extra cylinder and some accessories. I made a cover-piece to fit inside the glass and hold everything securely in place. The interior is lined in green felt.
The tools include a cleaning-rod, a screw-driver, a ball-setting tool and a bespoke powder flask that throws the correct charge for this revolver. There is room for a tin of percussion-caps, balls and wads as well as fifteen rounds of .44 Colt ammunition.
Some details of the gun- the breech-plate for the cartridge cylinder follows the contour of the blast-shield, allowing you to easily determine if the cylinder is loaded.
The rear-sight trough is deep and wide, and actually provides an excellent sight picture for a gun of this type. The gun is very comfortable for my hand and the gun points quite naturally. I'm really looking forward to getting this to the range and shooting it, both as a percussion gun and with cartridges. It will be interesting to see if it hits anywhere near point of aim...
Oh, for display purposes the internal cover can be removed so that the gun can be seen through the glass.
This is one of my more elaborate builds, and I am quite happy with the way it has come out.