https://youtu.be/Q47N9UTjydw?si=tm1DqfwcZbxb6C_g
The new Individual Weapon System, chambered in a new .264 round, was on display in a case, tucked away in the military section of FN America’s booth. On first sight you might mistake the rifle for a SCAR-H or an AR-10 pattern marksman’s rifle but on closer inspection the rifle is a different beast. With the weapon only displayed inside the case this is the best footage I could get of it.
FN explained that the new weapon and ammunition was developed for the Irregular Warfare Technology Support Directorate (IWTSD). Interestingly, the aim for the project was to provide overmatch against emerging great power competitors and future threats. A similar goal to the US Army’s Next Generation Squad Weapon System which coalesced on a 6.8mm round. It’s important to note, however, that the IWS was not FN’s proposal for NGSW – that instead was based around an adapted FN HAMR and a belt-fed weapon in 6.8mm.
What is the IWTSD? The Irregular Warfare Technology Support Directorate is responsible for carrying out research and development to support U.S. and allied organisations involved in irregular warfare. Originally set up in 1999 as the Combating Terrorism Technical Support Office, its name was changed in 2021.
The IWS chambers the Lightweight Intermediate Caliber Cartridge (LICC), developed from .264 USA. The 6.5x43mm round uses a steel case, which FN America says reduces weight by 20% compared to equivalent brass. No data on velocities has been released yet. The round has a two-piece, lightweight steel design with a stainless steel head and case body. A variety of loads have been developed with a number of different projectiles, including a 130gr Reduced Ricochet Limited Penetration round, a 109gr copper open tip match (OTM), a 120gr copper OTM and a soft nose 125gr cartridge. To date FN haven’t yet released any data on the rounds performance.
According to the 2019 Broad Agency Announcement (BAA), which outlined the programme’s requirements, polymer cased ammunition was considered and two proof of concept rounds were desired for Phase 1: 108gr OTM with a muzzle velocity of 2650 feet per second, from an 11.5 inch test barrel, and a frangible training round.
In Phase 2 IWTSD required Combat Barrier rounds loaded with Special Operations Science and Technology (SOST-style) projectiles and an M855A1-style enhanced penetration round which could penetrate no less than 12-inches of 10% ordnance gelatin at 800m and no greater than 18 inch at 25m-150m when fired from a 14.5 inch barrel or 25m-450m when fired from a 11.5 inch barrel.
A new 25 round polymer magazine has been developed for the rifle, sized somewhere between a 5.56x45mm STANAG magazine and a 7.62×51mm AR-10 pattern magazine. The proprietary magazine was developed by an industry partner – believed to be Magpul. FN say that when fully-loaded loaded with 25 rounds it is equivalent in weight to a Magpul P-Mag loaded with 30 rounds of 5.56mm ammunition. From the IWTSD 2019 BAA we know that a box magazine no longer than a STANAG magazine with a “self-lubricating non-tilt follower and high-quality corrosion resistant magazine spring” which could be loaded with ammunition in stripper clips using speed loaders was required
FN’s Individual Weapon System in .264 USA
There was significant buzz around FN America’s booth at SHOT 2023 a couple of months ago. FN America unveiled a brand new rifle, developed for a US government requirement. I had the chance to take …
armourersbench.com
The new Individual Weapon System, chambered in a new .264 round, was on display in a case, tucked away in the military section of FN America’s booth. On first sight you might mistake the rifle for a SCAR-H or an AR-10 pattern marksman’s rifle but on closer inspection the rifle is a different beast. With the weapon only displayed inside the case this is the best footage I could get of it.
FN explained that the new weapon and ammunition was developed for the Irregular Warfare Technology Support Directorate (IWTSD). Interestingly, the aim for the project was to provide overmatch against emerging great power competitors and future threats. A similar goal to the US Army’s Next Generation Squad Weapon System which coalesced on a 6.8mm round. It’s important to note, however, that the IWS was not FN’s proposal for NGSW – that instead was based around an adapted FN HAMR and a belt-fed weapon in 6.8mm.
What is the IWTSD? The Irregular Warfare Technology Support Directorate is responsible for carrying out research and development to support U.S. and allied organisations involved in irregular warfare. Originally set up in 1999 as the Combating Terrorism Technical Support Office, its name was changed in 2021.
The IWS chambers the Lightweight Intermediate Caliber Cartridge (LICC), developed from .264 USA. The 6.5x43mm round uses a steel case, which FN America says reduces weight by 20% compared to equivalent brass. No data on velocities has been released yet. The round has a two-piece, lightweight steel design with a stainless steel head and case body. A variety of loads have been developed with a number of different projectiles, including a 130gr Reduced Ricochet Limited Penetration round, a 109gr copper open tip match (OTM), a 120gr copper OTM and a soft nose 125gr cartridge. To date FN haven’t yet released any data on the rounds performance.
According to the 2019 Broad Agency Announcement (BAA), which outlined the programme’s requirements, polymer cased ammunition was considered and two proof of concept rounds were desired for Phase 1: 108gr OTM with a muzzle velocity of 2650 feet per second, from an 11.5 inch test barrel, and a frangible training round.
In Phase 2 IWTSD required Combat Barrier rounds loaded with Special Operations Science and Technology (SOST-style) projectiles and an M855A1-style enhanced penetration round which could penetrate no less than 12-inches of 10% ordnance gelatin at 800m and no greater than 18 inch at 25m-150m when fired from a 14.5 inch barrel or 25m-450m when fired from a 11.5 inch barrel.
A new 25 round polymer magazine has been developed for the rifle, sized somewhere between a 5.56x45mm STANAG magazine and a 7.62×51mm AR-10 pattern magazine. The proprietary magazine was developed by an industry partner – believed to be Magpul. FN say that when fully-loaded loaded with 25 rounds it is equivalent in weight to a Magpul P-Mag loaded with 30 rounds of 5.56mm ammunition. From the IWTSD 2019 BAA we know that a box magazine no longer than a STANAG magazine with a “self-lubricating non-tilt follower and high-quality corrosion resistant magazine spring” which could be loaded with ammunition in stripper clips using speed loaders was required