holster for 29-3

[cmccaslin528]

Last weekend I purchased a 29-3 with a 6.5" barrel. I am now looking for a left handed holster to carry this hand cannon. The gun will be used for carrying in the woods while hiking, riding ATVs, and just bumming around looking for stuff that "feels lucky". Most, but not all of the time I will be carrying I will be either on an ATV or in some other vehicle. Terrain could be anything from flat to fairly brushy with the occasional ATV ride through shallow water. What holster models would you all recommend? Belt carry or shoulder holster carry? If it matters, my build is a tall skinny guy. With regards to material I would prefer leather.

 

[g_gunter]

Take a look at this one.

I just got this in for my 6.5" 29-3 yesterday and love it. You may have to call them to make sure they have it for a lefty, though. I decided to go this bandoleer route so that I can wear it over my cold weather gear to back up my rifle. Probably the single best holster decision I've made so far (except for my Brommeland).

http://www.sportsmansguide.com/cb/cb.asp?a=119742

Greg

 

[Bullet Bob]

1. 29-3's should have 6" barrel, not 6.5".

2. If you're going to be sitting a lot, a shoulder holster is the way to go - barrels over 4" can get downright uncomfy when seated. I like El Paso saddlery's "tanker" style - easy to take on and off, quality leather and workmanship. If you definitely wanted a waist style holster, the "Tom Threeperson's" crossdraw style is good for longer barrels.

 

[cmccaslin528]

Bullet Bob, I have looked at the "tanker" holster from El Paso but I have a few questions about it. Number one, where does it position the gun, across the chest? Number two is my 29-3 is of course blued. I am concerned about exposing the frame in case I encounter heavy brush, dust, etc. Also concerned about protecting the finish of the gun in the holster, is the holster lined? It appears as though the tanker holster does leave part of the frame exposed. Will that exposure be a problem?

Anybody else feel free to reply as well!

 

[Bullet Bob]

The holster is lined, I can't remember if I had to pay extra or not; their website would probably let you know. You can slightly adjust the position if the holster, but it's more under the arm (though not in the armpit) than anything else. Your arm protects it from most brush, etx. El Paso Saddlery does have a full-flap belt holster if protection is your primary concern.

 

[BluesBear]

Yes, the 29-2 was the last to use the 6½" barrel. The 29-3 barrels were 6", even though every one I have ever handled was really 5-7/8".

But then all of the 4" ones are really 4¼". The 3" and 5" really are 3" and 5" though. Go figure.

 

[JMLV]

You want a full flap holster to protect the finish

on your blued gun. check with some of the custom makers for a crosdraw full flap design dhould not be a problem seated as its angled the flap and lining will protect your finish. You need to look at the custom makers like ghram or perhaps el paso mabe some others. I had Ron Ghram make my flap holster and I am very pleased with it.
Jim L

 

[azrael]

Lined holsters protect the finish?? really?? hmmm you sure??


Anyways, I would go with a flap holster..Plain and simple...Either crossdraw or regular...

Not one that is "one size fits all" but one MOLDED to that weapon...Also get one that has a REALLY GOOD SNAP!...I looked at one the other day that someone had pawned with there gun and I can tell ya, a good snap is worth the extra 2 or 3 dollers..

yea a good flap holster made for that weapon will be a bit on the high side..But it will be well worth it, if your 4-wheeler decides to "slingshot" you really hard on the ground and you roll for prolly 25 ft. a$$ over teakettle...Wanna guess how I know that one??

Elpaso saddlery has some nice stuff..check them out..


FWIW..

I am EvadsweetdreamsaremadeofthisB.