Search results for query: *

Looking at load data for 12 gauge on the Hodgdon website. For AA hulls, lead shot, 1oz loads using REM 209 primers and WAA12SL wads, they list 4 different “maximum” loads for 700-X (15, 16.5, 18, and 19 grains). Is this their odd way of saying 15 grain minimum load and 19 grain max? Or am I...

Recently started wet tumbling and really like it. But I’ve began to get some brass shavings when loading. The cases don’t seem to be sticking, so I’m curious what the cause would be. Any ideas?

I’m looking into getting into wet tumbling but have a concern or two. First, does wet tumbling make brass stick when loading like when you buy new brass from Starling etc? I’ve read some people use Wash and Wax in their solution because the wax leaves a protectant film on the brass, but does it...

Wanting to try out loading 9mm 147 grainers for fun (plan on getting a few RMR FMJs). Available powders are 700-X and TiteGroup. My Lyman #49 manual has data for 147gr TMJ, which I know is Speer’s offering. Are those the same as FMJ, or can I use FMJs with that set of data? People seem to do...

Been loading pistol and rifle for a few years, but may be getting into shot shell loading next. My uncle is gifting me what appears to be everything I’ll need to get going MEC 650, 3 charge bars, 6 powder bushings, MEC resizer, 30lb of # 7 1/2 shot, 25 pound of #5 shot, 200 1 oz wads, 400 1 1/8...

First one, are Hornady HAP not the same as XTP? I’ve read that the HAP are pretty accurate projectiles, so I’d like to pick some up to try. I checked out my Hornady manual, and they’re not listed in the 9mm section, but it lists the 124gr XTP (the HAP are 125gr). The Hornady website makes it...

I have read that the Magpul stocks for the 590A1 partially covers the trigger guard and requires loosening/removing the stock to disassemble the shotgun. But everything I have found is a couple years old. Is this still true? Or has Magpul corrected the issue at this point?

Finally got to take my new Wilson to the range today, and I’m beyond impressed. Fit and finish are perfect, trigger is a crisp clean break, safety is nice and positive, and the orange front sight jumps out. Only have around 150 rounds of mixed 124gr FMJ factory, reloads, and Gold Dot. All...

Hello! I need a little help. I ordered sample packs of Blue Bullets 125 lead CN and SNS 125gr lead FP, to load in 9x19. I had data for 125gr lead, no designation as to profile, and it gives a 1.125” COL. The Blue Bullets seat to that just fine. Pass gauge test, plunk test, and feed from the mag...

Hello! I’m looking at getting a CZ P07 Urban Gray (suppressor ready), but am having trouble finding a holster. Are the P07 and P09 kinda like the Glock 17 and 19 in that a holster for a larger model generally works for a smaller one? Right now I’m just looking for a range holster and see that...

Haven't posted in a good bit, but here is my first "built to order" rifle. My awesome wife funded everything but the optic for my birthday. Aero Upper Aero lower Geissele SSA Magpul pistol grip Magpul stock Ballistic Advantage 18" 5.56 SPR barrel (rifle length gas) Midwest 15" free float rail...

Just picked up a G34 and need a holster. I was looking at the GCode OSH with RTI attachment. Is that IDPA legal? It looks like the RTI creates some additional standoff due to the attachment method. I don't want to get it then find out it's not legal. I only shoot local matches, if that matters.

I'm trying to make a cheap practice round that replicates my 124gr Gold Dot carry ammo, which Midway says clocks in at 1150 FPS. Berry's says to use lead or low to mid range jacketed data, AND that the bullets are rated for 1250 FPS. I can achieve the 1150 FPS according to my Speer manual, but...

I went shooting with a friend, and after shooting some drills, we closed out with a competition. Rules are simple. 25 rounds, 5 at 5 yards, 10 at 15 yards, and 10 at 25 yards. A hit in the X or 10 ring are worth 10 points, hits in the 9 ring are worth 9, etc. Max of 250. Number of hits in the X...

I'm picking up a model 637 next week, and it is my first revolver that I'll ever have owned. Is there anything special about revolvers that I should be aware of? Or are they pretty much like autos in terms of maintenance? What's a good defensive load for it? Being an air weight, I'm sure recoil...

I'm gonna pick up a Smith model 637 in a week or so, so naturally I am also going to pick up some dies etc to load for .38 Special. I already reload for several semi autos, but have never done any revolver reloading. Are there any quirks or things like that that I should be aware of? Or just...

Tried out my first batch of .380 reloads, and they failed horribly. Had failure to feeds and ejects in almost every magazine. I used 2.8gr TiteGroup, 100gr plated, and seated to .98". I'm unsure if the feeding issues were OAL or charge weight induced. Would it be a good idea to add a tenth to...

I loaded up some Everglades Ammo 100gr plated 380 bullets. They say to keep them under 1200 FPS (no issue with 380). I used 2.8gr TiteGroup, which is right in the middle of the data on Hodgdon's website for 100gr FMJ. Two questions. First, is that too hot? Glock 42's seem to prefer hotter...

Just got my Lee turret and other gear all set up and am having issues getting my Auto drum to meter 700-X consistently. I've cleaned it up and ran a hopper through it. It varies by .3-.4 grains sometimes. My uniflow doesn't have that issue. Is there anything I should try to get it to dial in...

Been loading on a Rock Chucker for a few years now, and want to upgrade to a turret press. Have no need or desire for a progressive. I've pretty much decided on a Lee, due to the auto indexing, but I'd like to make sure I'm not leaving out or forgetting anything important. Instead of getting the...