The inventory app that I have used for years is no longer supported by the developer. So I need a new one. I only use it for my gun inventory. I don’t need ammo inventory or range reports or ballistics information, etc. I’m not adverse to buying the app but I don’t want an ongoing payment...
My 629-3 has a target trigger that is sharply serrated and will irritate or cut my trigger finger depending on how much I shoot. I don’t want to “de-burr” it as I want to keep it original. I have a smooth trigger that I acquired years ago and I would like to use it on this gun, but most of my...
My Pact digital scale has started to get “drifty” and I am looking to replace it. On my retirement budget I have limitations. So I need to keep it under $200. I want to stay with a digital scale if possible. I need something dependable that doesn’t drift off zero every few minutes.
Please...
Most of the more recent reloading data that I see gives pressure data in PSI (pounds per square inch), but a lot of the published data is in CUP (copper units of pressure). I know that PSI uses a strain gage and CUP uses a copper crush disk, but is there any way to correlate the two results...
I’m having trouble finding “moderate “ .44mag loads for 255 grain “Keith” lswc bullets. I don’t want to go below the starting loads listed but most of the data I have starts at ~ 1100 FPS. But I have found several different loads in .44Spl. that I like. Would there be any problems with...
A fellow shooter recently sold me 500 rounds of .357 brass. While cleaning and inspecting it I noticed that the majority of it was CBC and PMC headstamp. I don’t have any experience with either of these brands and wondered if they are quality brass. I load some pretty hot .357 loads and...
Recently purchased a lightly used S&W model 60-15, 3” .357. Had a few handling “beauty marks “ but all minor. Took it o the range to try different loads. It shot to POA with factory.357 ammo, but there was always a “flier”. I thought it was probably me as full house .357 mags in a 3” J-frame...
Oops! Did I post this in the wrong place? Is so, please move.
I just got another S&W model 60 and the DA trigger is Very heavy. It’s fairly smooth, just heavy. I understand that the standard weight mainspring is 8.5#, but the only replacement springs I can find are 8#. That doesn’t seem...
Looking for a link to the 2005 Handloader Magazine article by Brian Pierce on .44 special loads. My computer died recently and I lost some data, including this article. I have seen it before but can’t find it now!
All help is appreciated! Ken
To remedy the 15 lbs + double action trigger pull on my S&W model 69. 2.75" revolver, I installed a Wolff level 2 mainspring. I started getting light strikes. Since this will be in my EDC rotation I immediately put the original spring back. To my surprise and frustration I am still getting...
I have a 550C and am considering a Dillon case feeder to simplify the reloading process.
(No I don't want to upgrade to a 650.)
Those of you who have or had a casefeeder, let's have your thoughts. Pros/Cons
Reliable? Worth the money? Too finicky?
Anything else out there that would work...
I have used a few different ones in the past but have never been satisfied with their accuracy or repeatability. Before I tackle a couple of trigger jobs I need to get a better one. I know there are lots of people on here that lots of experience, so I need some advice. Who's the best?
Thanks!
I recently purchased a S&W model 15-8. It has the MIM hammer and trigger. I want to know if it is possible to change out the MIM parts for standard steel parts. Before I buy the replacement parts, I thought I would check with the experts here to see if it is do-able. If it's possible I will...
I have a S&W 629-3 6" that has just over 1.5K round through it. About half were LSW handloads and half were factory JHP.
I have started to notice that the back side of the locking notches on the cylinder are starting to show some peening and there is a small raised burr on the back edge of...
I have a S&W Model 64-5 that is factory DAO. I want to convert it to DA/SA as I like to use SA some times. Can I replace the DA hammer with a standard hammer or will it require replacing the hammer and trigger?
Or is there any reason that this cannot be done?
I have a handgun that was given to me some time ago. It is a Beretta? .380 semiauto with a 3.25" barrel. The magazine holds 7 rounds, single stack, and has a pronounced extension at the bottom.
There are no markings on the pistol except for the serial no. G191XX on the right side of the...
I have a Springfield Ultra Compact V10 in .45acp. I have had the gun for several years and I like it. It functions reliably and is a good belt carry gun. The one thing I don't like is the ported barrel. The muzzle blast is really bad and it is impossible to see after the first shot in low...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.