Search results for query: *

What experience have you had using a case activated Hornady PM on a Dillon 650 tool head? Thanks, Scott

Recently acquired a Police Automatic Weapon System (P.A.W.S.) bullet collator as part of a larger purchase. It's probably 25 to 30 years old. The company was out of Salem, Oregon and is still listed but does not answer their phone. The connector plug to the limit switches or speed control...

What powders are acceptable for loading 50 BMG? Anyone have a favorite recipe? Thanks, Scott

Well...I started working on a progressive reloading setup for 5.7x28 in January of 2010 and just finished a 1000 round run yesterday. It was, in fact a pricey project but now it's done and works as it should. Here is the tale... 1) Custom size/trim die for my Dillon 1200 rapid trim - $55 from...

Are there any air gun shooter here? What are you shooting and what would you prefer to shoot? My new Beeman P11 .177 is a fantastic way to practice indoors. Thanks, Scott

I'm looking to restock a chopped up Steyr M95/30. I need a complete stock set with bands but would consider buying a ratted out gun with a decent stock to get the job done. Please PM me here. Thanks, Scott

I'm about to do my first chamber cast with Brownell's CerroSafe. Does anyone have "how to" or "how NOT to" cast a chamber? Rifle is a GEW 1888 Commission Rifle. Actually just looking to check caliber so I could simply check the barrel. Recommendations please? Scott

1. What's the different in these two caliber please? 2. Does anyone have a lite load for a Gew88? 3. Does anyone cast lead for this round? Thanks, Scott

Folks, I just checked the seating depth on a recent addition to my collection and found the measured OAL to be 3.310 compared to 3.150 indicated in my trusty LEE loading manual. In addition the LEE manual recommends seating to 3.025 for the 140 gr I have on the shelf which would be a .260...

Just purchased a Sabatti 33 LR with a Ruger 10/22 type action. It appears that the bolt locks back by raising a tab next to the trigger guard, however, the lock tab appear to be spring loaded and releases the bolt when I take my finger off of it. Anyone have experience with this rifle? Scott

Just ran first 50 reloads through my new FN FiveSeven (only 100 rounds of factory through it). Case trim and OAL carefully controlled with 4.9 to 5.0 gr True Blue (low end of Ramshot specs) and 40 gr Nosler BT. The report is quite a bit louder than factory and rack was a bit faster; but, the...

Anyone have load data for .41 Avenger please? Thanks, Scott

Bought this Lyman Grand American off the junk bench at a local shop for $20. It is piecey but disassembled easily for cleaned up. The folks at Lyman were good enough to photocopy a manual so I can get it set-up but they don't have parts anymore and I'm wondering if anyone here might have...

Anyone have a current source for clip on Clearsight shooting lense? Thanks, Scott

Can anyone provide a copy of the manual for a Lyman Grand American Shotshell Loader? Can anyone provide guidance for getting one set up? Thanks, Scott

A few years ago I acquired about 40 boxes of factory 16 ga bird shot from a guy moving to FL. Its probably 15 plus years old, has always been stored inside and kept dry. I just acquired a field grade Winchester Model 12 in 16 ga, 2 3/4 inch Mod. Serial number puts manufacture in 1937...

I picked up a Savage Model 63 just like the one I had when I was 10 at a gun show today. The stock has been poorly refinished and I like to straighten it out It looks like it takes a key to unlock the action from the stock. Does anyone know how this works please? Thanks, Scott

I had the good fortune of picking up a dirty, but salvageable Redding Model 3 powder measure at a gun show today...on an RCBS stand...for $10. Poor thing spent a lot of years in a smokers cave but it cleaned up nicely and appears none-the-worse for wear. I'm looking for recommendations on...

Anybody using a RCBS Lockout die on bottleneck cartridges on a LNL-AP? Thanks, Scott

Hey Guys, I'm working on an apples to apples comparison of the LNL AP and Dillon 650XL. I'm thinking this list is about as close as it comes for changing from caliber to caliber. Prices are current Graf list. Thoughts please? Scott Dillon 650 XL Shellplate and bushings for...