Hi,
I just took these are off an old Wingmaster that was put away and never shot. They are in about perfect/new condition. What would be considered a fair price?
Thanks,
Jason
Hi,
I'm considering getting a Winchester 69a.
What would be a fair price for one with standard sights in good shape?
Are there any known issues with these or anything specific that should be checked before buying?
Would they be a good choice for a .22lr bolt gun?
I appreciate...
Hi,
Has anyone used this swivel on their existing 870 mag cap? Does it really require any modification of the cap?
http://www.uncle-mikes.com/products/magnum_most_pumps_auto.html
Thanks,
Jason
Hi,
I'm planning to look at an older Remington 870 Wingmaster (1981) and was wondering what should be checked out when buying a shotgun. Is there a way to tell how much it has been shot?
Also, what would be a good price for an excellent condition Wingmaster with a 30" ribbed barrel...
Hi,
I'm considering a Ruger Secutity Six made in the late 80's. How would the quality then compare with Ruger's quality now? Just trying to get as much info as I can before I decide.
Thanks,
Jason
Hi,
I'm mostly familiar with Glocks and have never had any experience with aluminum framed handguns. I'm considering a P220. How does it hold up against the Glock in terms of reliability and durability? What about higher pressure rounds? I'm assuming the P220 has the edge as far as...
Hi,
Is there an easy, inexpensive way to attach a sling swivel to the barrel rather than the for-end of the stock? If the barrel is fully floated, with little to no support from the stock, would this be a good idea?
The rifle is a Swiss K31 with a cut down stock. If I could attach a...
Hi,
I have a chance to get an older S&W 4006 with the non-lazer-etched serial number.
Are they reliable? Are they well made? How much would one in good condition be worth?
Thanks for your help,
Jason
Hi,
I will be receiving my first .45 next week and wanted to start buying ammo now. I can get Blazer Brass for under $10 per 50 locally. Is this good stuff, or should I go with WWB?
Thanks,
Jason
Hi,
I have an opportunity to get a savage enfield N. 4 MK. 1 for 159.99 at Big 5. Is this a good deal? They are supposed to be in very good condition. Should I worry about bore conditions, pitting? I can't expect the bore to be like me K31, can I? Is a two groove barrel good?
Any...
I've gotten so much info from you guys, so I just wanted to give back a little. I had the most stubborn lead deposits in the forcing cone area of my blackhawk. Brushing alone would not do it. I bought a lead away cloth from kleen bore for about $2.50, and it not only removed the burn rings it...
I picked up a few boxes of Miwall 240 LSWC in .44spec (they were all out of .44mag). I read a little about the specials etching the inside of the cylinders and burn rings. If I only shot 150 of these I shouldn't expect any problems, right?
Thanks,
Jason
I can see just the slightest sliver of the cylinder on the left-hand side. Really, its just barely visable. Is this anything I should be worried about? A timing problem?
Thanks,
Jason
What do you guys think of Miwall's .44 mag 240gr SWC at 950fps? Would this be a pleasant target shooting load? Would it leave a lot of lead in the barrel? Would it be worth it to just find a FMJ load?
I will have my first introduction to the .44 mag very soon.
Thanks,
Jason
It has about 200 rounds through it. It's in excellent condition. Also, it has a 4 5/8 inch barrel. What would be a fair price? I have looked through old sales, but prices seem to range quite a bit.
Thanks,
Jason
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.