6mm Max cartridge was just brought to my attention by my FFL buddy.
This is from the website linked below.
Cartridge designers have struggled with 2.26 OAL, and having enough room for increased case capacity. Until recently, there hasn’t been a .378 case head cartridge available that has a 35 gr water capacity. This amount of water capacity is the engine that can power heavier, and high ballistics coefficient bullets up to 100 grs. The 6mm MAX can do this within the constraints of the AR-15, and function flawlessly. So the end result is that the 6mm MAX can push bullets 55 gr to 100 gr, and do it with the same 2.30 OAL. Some designs have emerged shorter and fatter to accommodate a bullet with better BC and enough powder for useful velocities. When comparing the water capacity of 24 Nosler (29 grs), 6.8 SPC (35 grs), 5.56 x45 NATO (28.5 grs), 6×45 (29 grs), 6 ARC (34 grs), 6.5 Grendel (35 grs), .224 Valkyrie (34.5 grs), and what do we get? For the cartridges with .378 case head, powder capacity is less than the 6mm MAX. For the cartridges with larger case heads, you get the same amount of powder or less than the 6mm MAX. The end result is that the 6mm MAX (35 grs) allows for a .378 mil-spec bolt face with full lug integrity and powder to push the heavies at useful velocities.
The 6mm MAX has unlocked the code on the .378 bolt face AR-15 cartridge. We were able to increase the OAL to 2.30 with the .350 Legend parent case, and magazine, which were originally designed for the AR-15, and function flawlessly. With the OAL set at 2.30 for all bullets 55 gr to 100 gr, we were able to keep bullet jump relatively consistent for the inherent accuracy across all bullet weights. We have been able to achieve 1 MOA accuracy with most bullet weights, and sub-MOA with premium target bullets.
BC Precision Ballistics has spent 3 years and thousands of hours in research and range time to get the 6mm MAX perfected. Our case is only slightly rebated for a well balanced cartridge maximizing capacity and 100% reliability. We designed the chamber for functionality in a repeater and for accuracy. Sometimes those two requirements conflict with each other as reliability requires loose tolerances, and accuracy requires tight tolerances. We consulted with many lifelong industry experts throughout the chamber/reamer design and listened to what they had to say. We utilize carbide reamers for our builds, and our tolerances are kept exact for predictable performance.
Wondering about accuracy? On Aug 6th, 2022, I competed with the 6mm MAX in F-Class with my local club the Central Texas Silhouette Association or CTSA. Full disclosure on me? I’m an old F-Open High Master. My normal competition gun is a .243 30” Bartlein barrel running 105 hybrids at 3050 fps with a stout load of H4831SC. The 6mm MAX is not a competitive F-Open cartridge by any stretch of the imagination, but I wanted to see an actual real world test of accuracy in the hot south Texas switching winds at 500 yards. I used a 24” Bartlein barreled hunting rig. This is the same bolt rifle pictured on this web site. It has 2600 rounds of testing down range, and is till holding sub-MOA with a load of H4895 tested to SAAMI standards of 53,000 psi. The load was 26.6 grs of H4895, and 90 gr Lapua Scenar-L at 2.30 OAL. This load was straight from our loading chart on this web site. After the 3rd relay my score was 568-6X. Nothing to write home about by F-Class standards, but in the world of hunting and rifle accuracy these rounds would have HARVESTED GAME."
Brian Cook
Im bring it up because I was critical of it after my initial read up on it, and I think I bummed my buddys trip, on it.... possibly unfairly.
To be fair I don't think its a bad cartridge, but it FEELs like a step backwards in terms of cost/performance.
Being based on the.350 it does have a capacity advantage over the 6x45, TCU, x47 etc. AND it dosent exert the bolt thrust@ =psi, or weaken the lugs like .43 face or larger cases do.
After that it seems like were kinda going backwards.
Even medium length hunting bullets will be shoved well down into the case to achieve the 2.3" coal, which is a little long. Tho since its suppose to use 350 mags that might not mater.
Very straight walls, and what looks like a sharp shoulder also strike me as possibly problematic, But my experience with those case types are in bolt guns previously chambered for a more tapered cartridge
MY major gripe tho, is that it dosent seem like it can offer a real world advantage over a 6x45 (etc) that exceeds the difficulties and possible problems caused by using a unique case and the design.
I ran a 6x47 which would get very close or better to the suggested velocities from its 24" barrel, but mine was a bolt gun loaded over 2.3" and to unknown pressures specs.
And i do want to add that I whole heartedly support any cartridge creation, and anyone who wants to use it, but when asked my personal opinion ......thats what youll get
Now my question is.... Am I off base on my assessment, and/or being overly critical?
This is from the website linked below.
"Why The 6mm MAX?
The 6mm MAX is pressure tested to SAAMI standards of 55k psi. It is a brand new cartridge designed for the unmodified mil-spec .378 bolt face, and a full mass bolt carrier group. The 6mm MAX holds 35 grains of water capacity which ultimately determines the energy potential of the cartridge. In this case, 1750+Lbs of energy. Why is that so significant? The 6mm MAX can launch an 87 gr Berger VLD at 3009 fps from a 24” barrel. This produces 1749 lbs at the muzzle, 1504 lbs at 100 yards, 1093 lbs at 300 yards, 775 lbs at 500 yards, 533 lbs at 700 yards, and stays supersonic past 1000 yards. These ballistics are at standard atmospheric pressure and temperature.Cartridge designers have struggled with 2.26 OAL, and having enough room for increased case capacity. Until recently, there hasn’t been a .378 case head cartridge available that has a 35 gr water capacity. This amount of water capacity is the engine that can power heavier, and high ballistics coefficient bullets up to 100 grs. The 6mm MAX can do this within the constraints of the AR-15, and function flawlessly. So the end result is that the 6mm MAX can push bullets 55 gr to 100 gr, and do it with the same 2.30 OAL. Some designs have emerged shorter and fatter to accommodate a bullet with better BC and enough powder for useful velocities. When comparing the water capacity of 24 Nosler (29 grs), 6.8 SPC (35 grs), 5.56 x45 NATO (28.5 grs), 6×45 (29 grs), 6 ARC (34 grs), 6.5 Grendel (35 grs), .224 Valkyrie (34.5 grs), and what do we get? For the cartridges with .378 case head, powder capacity is less than the 6mm MAX. For the cartridges with larger case heads, you get the same amount of powder or less than the 6mm MAX. The end result is that the 6mm MAX (35 grs) allows for a .378 mil-spec bolt face with full lug integrity and powder to push the heavies at useful velocities.
The 6mm MAX has unlocked the code on the .378 bolt face AR-15 cartridge. We were able to increase the OAL to 2.30 with the .350 Legend parent case, and magazine, which were originally designed for the AR-15, and function flawlessly. With the OAL set at 2.30 for all bullets 55 gr to 100 gr, we were able to keep bullet jump relatively consistent for the inherent accuracy across all bullet weights. We have been able to achieve 1 MOA accuracy with most bullet weights, and sub-MOA with premium target bullets.
BC Precision Ballistics has spent 3 years and thousands of hours in research and range time to get the 6mm MAX perfected. Our case is only slightly rebated for a well balanced cartridge maximizing capacity and 100% reliability. We designed the chamber for functionality in a repeater and for accuracy. Sometimes those two requirements conflict with each other as reliability requires loose tolerances, and accuracy requires tight tolerances. We consulted with many lifelong industry experts throughout the chamber/reamer design and listened to what they had to say. We utilize carbide reamers for our builds, and our tolerances are kept exact for predictable performance.
Wondering about accuracy? On Aug 6th, 2022, I competed with the 6mm MAX in F-Class with my local club the Central Texas Silhouette Association or CTSA. Full disclosure on me? I’m an old F-Open High Master. My normal competition gun is a .243 30” Bartlein barrel running 105 hybrids at 3050 fps with a stout load of H4831SC. The 6mm MAX is not a competitive F-Open cartridge by any stretch of the imagination, but I wanted to see an actual real world test of accuracy in the hot south Texas switching winds at 500 yards. I used a 24” Bartlein barreled hunting rig. This is the same bolt rifle pictured on this web site. It has 2600 rounds of testing down range, and is till holding sub-MOA with a load of H4895 tested to SAAMI standards of 53,000 psi. The load was 26.6 grs of H4895, and 90 gr Lapua Scenar-L at 2.30 OAL. This load was straight from our loading chart on this web site. After the 3rd relay my score was 568-6X. Nothing to write home about by F-Class standards, but in the world of hunting and rifle accuracy these rounds would have HARVESTED GAME."
Brian Cook
Home - BC Precision Ballistics - Home of the 6mm Max®
bcprecisionballistics.com
Im bring it up because I was critical of it after my initial read up on it, and I think I bummed my buddys trip, on it.... possibly unfairly.
To be fair I don't think its a bad cartridge, but it FEELs like a step backwards in terms of cost/performance.
Being based on the.350 it does have a capacity advantage over the 6x45, TCU, x47 etc. AND it dosent exert the bolt thrust@ =psi, or weaken the lugs like .43 face or larger cases do.
After that it seems like were kinda going backwards.
Even medium length hunting bullets will be shoved well down into the case to achieve the 2.3" coal, which is a little long. Tho since its suppose to use 350 mags that might not mater.
Very straight walls, and what looks like a sharp shoulder also strike me as possibly problematic, But my experience with those case types are in bolt guns previously chambered for a more tapered cartridge
MY major gripe tho, is that it dosent seem like it can offer a real world advantage over a 6x45 (etc) that exceeds the difficulties and possible problems caused by using a unique case and the design.
I ran a 6x47 which would get very close or better to the suggested velocities from its 24" barrel, but mine was a bolt gun loaded over 2.3" and to unknown pressures specs.
And i do want to add that I whole heartedly support any cartridge creation, and anyone who wants to use it, but when asked my personal opinion ......thats what youll get
Now my question is.... Am I off base on my assessment, and/or being overly critical?
Last edited: