Search results for query: *

  • Users: cdet69
  • Content: Threads
  • Order by date
  1. C

    Extractor a post 64 model 70

    My friend has a Winchester model 70 post 64 in 243 Winchester. On the barrel it is stamped Winchester Model 70 Light weight 243 Winchester. What type of extractor parts would be needed? The extractor is missing and needs to be replaced.
  2. C

    Timney trigger in a Remington 722

    Has anyone ever used a Timney trigger in a Remington 722?
  3. C

    Nosler shots?

    Are the Nosler shots in 224 cal 55 grain the same as the Midway Dogtown bullets and the Midsouth Varmint Nightmare extreme?
  4. C

    Redding balance beam scale

    Anyone use this type of balance beam scale? I am thinking of getting one because my electronic scales keep going bad. I have a cheap Lyman balance beam but it is only a back up and realy not up to the task for everyday use.
  5. C

    Temperature problems?

    I was shooting my 222 Remington today and have noticed that the cases coming out showed some flattening of the head stamp. It was about 101 degrees and after shooting three rounds the barrel was becoming real hot. This is not normal for this rifle as it does not heat up very fast. The loads were...
  6. C

    Target crown for a Ruger 77MK II

    I am thinking of putting a target crown on a Ruger 77 MK II in 6.5X55 SE. Anyone ever put a target crown on one? Also any ideas on how to improve accuracy on one. thanks.
  7. C

    case longevity?

    Will cases last longer with cast bullets vrs. metal jacketed ones?
  8. C

    Winchester model 52 stock

    Are the model 52B and 52C stocks the same or similar?
  9. C

    Winchester 1300 magazine cap

    Is the magazine cap for the Winchester model 1300 12 guage the same as the one for the 20 guage?
  10. C

    Winchester Model 52c

    Looking for a Winchester Model 52c replacement stock. Any ideas on were I can find one.
  11. C

    The BHN off 50/50 bar solder

    Anyone know the @BHN of 5/50 bar solder?
  12. C

    BHN of wheel weights

    Does any one know the approximate BHN of bullets made from wheel weights and water quenched?
  13. C

    Benelli Nova

    Anyone ever use one and what are your thoughts about it. Are they any good and worth the money?
  14. C

    aluminum gas checks

    Anyone ever use these? Any idea on there negative properties ie: aluminum oxide the same stuff used in sandpaper.
  15. C

    Burris speed bead

    Anyone ever use the Burris speed bead? Did you like it and what were the pluses and minuses of it?
  16. C

    Raising point of impact

    Any ideas on how to raise the point of impact on a shotgun. The shotgun is a Mossberg 835 with a vent rib barrel. It is the camo turkey version. It is hitting about 6" low when only using the front bead.
  17. C

    Winchester synthetic stocks

    Anyone ever had problems with a Winchester synthetic stock? They do not appear to be very well made. There is very little bedding surface and they have massive open chanels. I have a Winchester Model 70 in 7MM STW in one of these stocks and it does not shoot very accurate. Any ideas on what to...
  18. C

    Forming 222 Remington from 223 Remington.

    Anyone ever form 222 Remington fron 223 Remington? Do you use a form and trim die and if soe who made it?
  19. C

    Peep sight for Ruger 44 magnum carbine

    I have the older style Ruger 44 Magnum carbine with the tube magazine. it has six mounting holes on top and I am looking for a peep sight that would fit it. Anyone know who might make one? Thanks
  20. C

    Mossberg 835 front sight thread

    Anyone know what size the thread is on the front sight of a Mossberg 835?
Back
Top